From: Fernando Carvalho (fernando.cagica@t-online.de)
Date: Mon Dec 03 2007 - 06:09:43 ART
Hi,
it will never work with the described scenario, you must either change
the ip ospf network type or use two different virtual-templates with
different ip addresses on the hub (can be on the same network). This is
due to the fact that in networks type "ip ospf network type p2p" each
interface shoud have no more than one neighbor. Even if you have 2
virtual-templaates with the same ip address will be one logical l3
interface with more than one neighbor- in wwhich case jsut one will be
recognized.
HTH
-----Urspr|ngliche Nachricht-----
Von: Vladimir Sousa [mailto:vladrac@gmail.com]
Gesendet: Sonntag, 2. Dezember 2007 23:35
An: Fernando Carvalho
Cc: iosluver@gmail.com; ccielab@groupstudy.com
Betreff: Re: OSPF Issue
Did anyone get this working?
I still get:
Adv Router is not-reachable
For one of the spokes on the HUB, show ip ospf data router
Vlad
On 11/29/07, Fernando Carvalho <fernando.cagica@t-online.de> wrote:
Hi,
Have you tried with 2 interfaces Virtualtemplate with the same ip
address on R4? So that R4 clones from different templates, building 2
p2p interfaces with the same ip address.
-----Urspr|ngliche Nachricht-----
Von: nobody@groupstudy.com [mailto:nobody@groupstudy.com
<mailto:nobody@groupstudy.com> ] Im Auftrag von
iosluver@gmail.com
Gesendet: Mittwoch, 28. November 2007 16:22
An: ccielab@groupstudy.com
Betreff: OSPF Issue
Hi GS,
I wanted to get some opinions on a task I came across which behaved in a
manner I didn't expect. Here are the details:
R3 -----Frame-Relay------- R4 -----Frame-Relay-------R5
Instructions:-
**********************
Use R4 as Hub.
Use only physical interfaces on R4 & R3
Use a sub-interface on R5
Do not use FRAME-RELAY MAP command on R5
Do not use any DYNAMIC layer 3 to 2 mappings on these connections DO not
send redundant broadcast traffic to the spokes Configure OSPF Area 0 on
the segment between R3,R4 & R5 Do not use IP OSPF NETWORK command.
Here is what I did:-
R3
****
interface Serial1/1
encapsulation frame-relay
frame-relay interface-dlci 314 ppp Virtual-Template1
interface Virtual-Template1
ip address 142.1.0.3 255.255.255.0
ip ospf hello-interval 3
!
router ospf 1
router-id 150.1.3.3
log-adjacency-changes
network 142.1.0.3 0.0.0.0 area 0
network 150.1.3.3 0.0.0.0 area 0
!
R4
***
interface Serial1/0
no ip address
encapsulation frame-relay
frame-relay interface-dlci 405 ppp Virtual-Template1 frame-relay
interface-dlci 413 ppp Virtual-Template1
interface Virtual-Template1
ip address 142.1.0.4 255.255.255.0
ip ospf network point-to-multipoint
ip ospf hello-interval 3
!
router ospf 1
router-id 150.1.4.4
log-adjacency-changes
network 142.1.0.4 0.0.0.0 area 0
network 150.1.4.4 0.0.0.0 area 0
R5
***
interface Serial1/0.504 multipoint
frame-relay interface-dlci 504 ppp Virtual-Template1
!
interface Virtual-Template1
ip address 142.1.0.5 255.255.255.0
ip ospf hello-interval 3
!
router ospf 1
router-id 150.1.5.5
log-adjacency-changes
network 142.1.0.5 0.0.0.0 area 0
network 150.1.5.5 0.0.0.0 area 0
The solution did not change the network type on R4 as its a violation of
the one of instructions. Without that command, R4 does not ANY certain
routes learnt from R3 to its routing table. It does however forward the
LSAs to R3 which installs them as valid routes which can't be reached
via R4. For obvious reasons I reduced the hello time. Some
output(connected routes) were removed for brevity. All suggestions are
welcome. I can send more debugs, log messages if required. Let me know
what you think.
R3 Routing Table
****************
O 150.1.5.5/32 [110/3] via 142.1.0.4, 00:02:09, Virtual-Access2
O 150.1.4.4/32 [110/2] via 142.1.0.4, 00:02:11, Virtual-Access2
R4 Routing Table
****************
Rack1R4#sh ip route
C 150.1.4.0/24 is directly connected, Loopback0
O 150.1.5.5/32 [110/2] via 142.1.0.5, 00:02:41, Virtual-Access3
R5 Routing Table
*****************
150.1.0.0/16 is variably subnetted, 3 subnets, 2 masks
O 150.1.4.4/32 [110/2] via 142.1.0.4, 00:05:34, Virtual-Access2
O IA 150.1.3.3/32 [110/3] via 142.1.0.4, 00:05:34, Virtual-Access2
OSPF DATABASE - R4 - Without point-to-multipoint
************************************************
Adv Router is not-reachable
LS age: 491
Options: (No TOS-capability, DC)
LS Type: Router Links
Link State ID: 150.1.3.3
Advertising Router: 150.1.3.3 <http://150.1.3.3>
LS Seq Number: 80000009
Checksum: 0x63B9
Length: 48
Area Border Router
Number of Links: 2
OSPF DATABASE - R4 - with point-to-multipoint
*********************************************
Routing Bit Set on this LSA
LS age: 264
Options: (No TOS-capability, DC)
LS Type: Router Links
Link State ID: 150.1.3.3
Advertising Router: 150.1.3.3
LS Seq Number: 80000009
Checksum: 0x63B9
Length: 48
Area Border Router
Number of Links: 2
Many Thanks in advance
This archive was generated by hypermail 2.1.4 : Tue Jan 01 2008 - 12:04:28 ARST