From: Scott Morris (swm@emanon.com)
Date: Sun Oct 14 2007 - 20:30:14 ART
Well, you appear to have an IP address which is good. I'll assume that the
VLAN information is correct.
What other parameters from DHCP are you passing? Are they all correct?
Do you have it configured in CM as either a gateway, a transcoder or
conference bridge?
HTH,
Scott Morris, CCIE4 (R&S/ISP-Dial/Security/Service Provider) #4713, JNCIE-M
#153, CISSP, et al.
CCSI/JNCI-M/JNCI-ER
VP - Technical Training - IPexpert, Inc.
IPexpert Sr. Technical Instructor
A Cisco Learning Partner - We Accept Learning Credits!
smorris@ipexpert.com
Telephone: +1.810.326.1444
Fax: +1.810.454.0130
http://www.ipexpert.com
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
Irfan Siddiqui
Sent: Sunday, October 14, 2007 2:45 PM
To: ccielab@groupstudy.com
Subject: Problem registering the gateway - please help
Dear All,
I am stuck at gateway . 6608 is not registered with Call manager. I am doing
exactly as per solution guide of IPexpert. This is the Lab Section 4.
Please help ??
here is the config and sh port config of 6509.
Here is the config of call manager gateway
Product : Cisco Catalyst 6000 E1 VoIP Gateway
Gateway : S0/DS1-0@SDA0019AAF51C8A
Device Protocol: Digital Access PRI
Registration: Unknown
IP Address:
Device Information
MAC Address*
Description
Device Pool* --- Not Selected ---BR1BR2HQ
Call Classification* --- Not Selected ---OnNetOffNetUse System Default
Network Locale < None >United States
Media Resource Group List < None >
Location < None >BR1HQ
AAR Group < None >
Load Information
Multilevel Precendence and Preemption (MLPP) Information
MLPP Domain (e.g., "0000FF")
MLPP Indication Not available on this device
MLPP Preemption Not available on this device
Interface Information
PRI Protocol Type* -- Not Selected ---PRI EUROPRI AUSTRALIANPRI QSIG E1
Protocol Side* --- Not Selected ---NetworkUser
Channel Selection Order* --- Not Selected ---Bottom UpTop Down
Channel IE Type* --- Not Selected ---Timeslot NumberSlotmapUse Number when
1BContinuous Number
PCM Type* --- Not Selected ---A-law5-law
Delay for first restart (1/8 sec ticks)
Delay between restarts (1/8 sec ticks)
Inhibit restarts at PRI initialization
Enable status poll
CCIEVOICE6500> (enable)
CCIEVOICE6500> (enable) sh runn
This command shows non-default configurations only.
Use 'show config all' to show both default and non-default configurations.
.................
..........................
.............................
.............................
......................
..
begin
!
# ***** NON-DEFAULT CONFIGURATION *****
!
!
#time: Sun Oct 14 2007, 05:24:20 EDT
!
#version 7.6(1)
!
set enablepass $2$CBqb$8Ve8Pb3kGzRkKuBUmNNQa1 !
#errordetection
set errordetection portcounter enable
!
#system
set system name CCIEVOICE6500
!
#!
#vtp
set vtp domain ccievoice
set vtp v2 enable
set vlan 1 name default type ethernet mtu 1500 said 100001 state active set
vlan 200 rspan name RSPAN state active set vlan 1002 name fddi-default type
fddi mtu 1500 said 101002 state active set vlan 1004 name fddinet-default
type fddinet mtu 1500 said 101004 state activ e bridge 0x0 stp ieee set vlan
1005 name trbrf-default type trbrf mtu 4472 said 101005 state active br idge
0xf stp ibm set vlan 210,220,240 set vlan 1003 name trcrf-default type trcrf
mtu
4472 said 101003 state active pa rent 1005 ring 0xccc mode srb aremaxhop 7
stemaxhop 7 backupcrf off !
#ip
set interface sc0 1 10.4.0.100/255.255.255.0 10.4.0.255 set interface sc1 0
0.0.0.0/0.0.0.0 0.0.0.0 set interface sc1 down
set ip alias default 0.0.0.0
!
#syslog
set logging level ethc 2 default
set logging level gl2pt 2 default
!
#ntp
set ntp client enable
set ntp server 10.4.200.3
set timezone est -5 0
set summertime enable EDT
!
#set boot command
set boot config-register 0x2
set boot system flash bootflash:cat6000-supk8.7-6-1.bin !
#igmp
set igmp disable
!
#qos
set qos wrr 2q2t 5 255
set qos wrr 1p2q2t 5 255
set qos wred 1p2q2t tx queue 1 40:80 70:100 set qos wred 1p2q2t tx queue 2
40:80 70:100 !
# default port status is enable
!
!
#module 1 : 2-port 1000BaseX Supervisor
set spantree portfast 1/1-2 disable
!
#module 2 : 48-port 10/100BaseTX Ethernet set trunk 2/1 nonegotiate dot1q
1-1005,1025-4094
set spantree portfast 2/1-48 disable
!
#module 3 : 48-port 10/100BaseTX Ethernet set vlan 240 3/5,3/8 set port
auxiliaryvlan 3/31 240 set port auxiliaryvlan 3/32 240
set port speed 3/1-2,3/5 100
set port duplex 3/1-2,3/5 full
set trunk 3/1 on dot1q 1-1005,1025-4094 set trunk 3/22 on dot1q
1-1005,1025-4094 set trunk 3/31 auto negotiate 1-1005,1025-4094 set trunk
3/32 auto negotiate 1-1005,1025-4094
set spantree portfast 3/1,3/22,3/31-32 enable
!
#module 4 : 8-port E1
set port voice interface 4/1 dhcp enable vlan 240 set port voice interface
4/2 dhcp enable vlan 240 set port voice interface 4/3 dhcp enable vlan 240
set port voice interface 4/4 dhcp enable vlan 220 set port voice interface
4/5 dhcp enable vlan 220 set port voice interface 4/6 dhcp enable vlan 220
set port name 4/1 POD11-PSTN-T1
set port name 4/2 POD11-CONFBRDG
set port name 4/3 POD11-TRNSCDR
!
#module 5 empty
!
#module 6 empty
!
#module 7 empty
!
#module 8 empty
!
#module 9 empty
!
#module 15 : 1-port Multilayer Switch Feature Card !
#module 16 empty
end
CCIEVOICE6500> (enable) sh port 4/1
* = Configured MAC Address
Port Name Status Vlan Duplex Speed Type
----- -------------------- ---------- ---------- ------ ----- ------------
4/1 POD11-PSTN-T1 enabled 240 full - unknown
Port DHCP MAC-Address IP-Address Subnet-Mask
-------- ------- ----------------- --------------- ---------------
4/1 enable 00-19-aa-f5-1c-8a 10.4.200.122 255.255.255.0
Port Call-Manager(s) DHCP-Server TFTP-Server Gateway
-------- ----------------- --------------- --------------- ---------------
4/1 - 10.4.200.21 10.4.200.21 10.4.200.3
Port DNS-Server(s) Domain
-------- ----------------- -------------------------------------------------
4/1 - -
Port CallManagerState DSP-Type
-------- ---------------- --------
4/1 notregistered C549
Port NoiseRegen NonLinearProcessing
----- ---------- -------------------
4/1 - -
Port Trap IfIndex
----- -------- -------
4/1 disabled 12
Port Status ErrDisable Reason Port ErrDisableTimeout Action on
Timeout
---- ---------- ------------------- ----------------------
-----------------
4/1 enabled - Enable No Change
Idle Detection
--------------
--
CCIEVOICE6500> (enable) 2007 Oct 14 05:24:42 EDT -04:00
CCIEVOICE6500> %SYS-4-MODHPRESET:Host p
Thanks and regards
J P Singh
**********************************************************************
Any opinions expressed in the email are those of the individual and not
necessarily the company. This email and any files transmitted with it are
confidential and solely for the use of the intended recipient. If you are
not the intended recipient or the person responsible for delivering it to
the intended recipient, be advised that you have received this email in
error and that any dissemination, distribution, copying or use is strictly
prohibited.
If you have received this email in error, or if you are concerned with the
content of this email please e-mail to: e-security.support@vanco.info
The contents of an attachment to this e-mail may contain software viruses
which could damage your own computer system. While the sender has taken
every reasonable precaution to minimise this risk, we cannot accept
liability for any damage which you sustain as a result of software viruses.
You should carry out your own virus checks before opening any attachments to
this e-mail.
Vanco UK Ltd Registered in England No: 2296733 Registered Office: John Busch
House, 277 London Road, Isleworth, Middlesex TW7 5AX
Please consider the environment before printing this e-mail
**********************************************************************
This archive was generated by hypermail 2.1.4 : Fri Nov 16 2007 - 13:11:14 ART