From: Biggs, Jeff \(M/CIO/BIE\) (JBiggs@usaid.gov)
Date: Wed Sep 19 2007 - 10:50:24 ART
AUX ROUTER CONFIG
sh run | beg line
line con 0
password cisco
stopbits 1
line aux 0
login local
modem InOut
transport input all
transport output all
stopbits 1
line 66
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
line vty 0 4
password cisco
login
*********************************************************************************************************************************************
CONSOLE ROUTER CONFIG
sh run | beg line
line con 0
password cisco
login
transport preferred none
transport output none
stopbits 1
line aux 0
login local
modem InOut
transport input all
transport output telnet
stopbits 1
line 66
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
line vty 0 4
password cisco
login
Jeffrey Biggs
Sr. Network Engineer
M/CIO/BIE
CCNP, CCDA
240-646-5003
jbiggs@usaid.gov
This e-mail is intended for the addressee only. If you are not the intended recipient, please be aware that the unauthorised use or disclosure of the information it contains, or the unauthorised copying or re-transmission of the e-mail are strictly prohibited. Such action may result in legal proceedings. If the e-mail has been sent to you in error, please accept our apologies, advise the sender as soon as possible and then delete the message. Under the Freedom of Information Act 2000 / Data Protection Act 1998, the contents of this e-mail, whether it is marked confidential or otherwise, may be disclosed.
-----Original Message-----
From: Gregory Gombas [mailto:ggombas@gmail.com]
Sent: Wednesday, September 19, 2007 9:34 AM
To: Biggs, Jeff (M/CIO/BIE)
Cc: ccielab@groupstudy.com
Subject: Re: Reverse Telnet issue
Its hooked up to your aux port right? Can you show the configuration
of the aux port?
I think you may need to specify transport input telnet...
On 9/19/07, Biggs, Jeff (M/CIO/BIE) <JBiggs@usaid.gov> wrote:
> Have a 3845 that I am trying to use to reverse telnet into another 3845.
> I get the following:
>
> TEST-CRR01#tel 10.1.1.254 2001
>
> Trying 10.1.1.254, 2001 ... Open
>
>
>
> But cannot get any further. I have tried a myriad of command setups and
> looked over many Cisco webpages on this, but no luck. Anyone have
> similar experiences with this platform? I do this on other platforms
> with no issues, just seems to be the 3845.
>
>
>
> Thanks,
>
>
>
> Jeffrey Biggs
>
> Sr. Network Engineer
>
> M/CIO/BIE
>
> CCNP, CCDA
>
> 240-646-5003
>
> jbiggs@usaid.gov <mailto:jbiggs@usaid.gov>
>
>
>
> This e-mail is intended for the addressee only. If you are not the
> intended recipient, please be aware that the unauthorised use or
> disclosure of the information it contains, or the unauthorised copying
> or re-transmission of the e-mail are strictly prohibited. Such action
> may result in legal proceedings. If the e-mail has been sent to you in
> error, please accept our apologies, advise the sender as soon as
> possible and then delete the message. Under the Freedom of Information
> Act 2000 / Data Protection Act 1998, the contents of this e-mail,
> whether it is marked confidential or otherwise, may be disclosed.
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Sat Oct 06 2007 - 12:01:13 ART