From: wilfred d'souza (wilfred_thegr8@yahoo.co.in)
Date: Sun Jul 29 2007 - 12:47:04 ART
I guess so...
Wilfred
viny gm <vinygm@gmail.com> wrote: i am not in US I am in Dubai, Still i need M1 or M2 ??
Viny
On 7/29/07, wilfred d'souza <wilfred_thegr8@yahoo.co.in> wrote: Your card will not support Caller ID. you need to have VIC-2FXO-M1 if in US.
Wilfred
viny gm <vinygm@gmail.com> wrote:
Here is show diag
2nd generation - FXO Voice daughter card (4 port)
Hardware Revision : 5.0
Top Assy. Part Number : 800-21589-02
Board Revision : A0
Deviation Number : 0-0
Fab Version : 04
PCB Serial Number : FOC10440NZ9
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : VIC2-4FXO
Version Identifier : V01
CLEI Code : CNUIAPRAAA
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 00 4C 41 05 00 C0 46 03 20 00 54 55 02
0x10: 42 41 30 80 00 00 00 00 02 04 C1 8B 46 4F 43 31
0x20: 30 34 34 30 4E 5A 39 03 00 81 00 00 00 00 04 00
0x30: CB 89 56 49 43 32 2D 34 46 58 4F 89 56 30 31 20
0x40: C6 8A 43 4E 55 49 41 50 52 41 41 41 FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
viny
On 7/29/07, wilfred d'souza <wilfred_thegr8@yahoo.co.in > wrote: can u also paste the show diag?
viny gm < vinygm@gmail.com> wrote: Debug error msg
----------------------
get_fxo_caller_id:Caller ID receive failed. parseCallerIDString:no data.
config
--------------
voice-port 0/1/0
cptone GB
timeouts call-disconnect 3
timeouts wait-release 3
connection plar opx 300
impedance complex2
caller-id enable
!
voice-port 0/1/1
cptone GB
timeouts call-disconnect 3
timeouts wait-release 3
connection plar opx 300
impedance complex2
caller-id enable
!
voice-port 0/1/2
cptone GB
timeouts call-disconnect 3
timeouts wait-release 3
connection plar opx 300
impedance complex2
caller-id enable
!
voice-port 0/1/3
cptone GB
timeouts call-disconnect 3
timeouts wait-release 3
connection plar opx 300
impedance complex2
caller-id alerting dsp-pre-allocate
dial-peer voice 200 voip
tone ringback alert-no-PI
translation-profile outgoing addinPrefix
preference 1
destination-pattern 3..
voice-class h323 1
session target ipv4:xx.xx.xx.xx
dtmf-relay h245-alphanumeric
codec g711ulaw
no vad
dial-peer voice 100 pots
preference 1
destination-pattern 9[2-9]......
port 0/1/0
!
dial-peer voice 101 pots
destination-pattern 9[2-9]......
port 0/1/1
!
dial-peer voice 102 pots
destination-pattern 9[2-9]......
port 0/1/2
!
dial-peer voice 103 pots
destination-pattern 9[2-9]......
Viny
On 7/29/07, wilfred d'souza <wilfred_thegr8@yahoo.co.in > wrote: Also your FXO Interface needs to be VIC-2FXO-M1 or VIC-2FXO-M2 for Caller ID Support.
Wilfred
Mark Snow <msnow@ipexpert.com> wrote: Two things - 1 are you using MGCP? While the gateway clearly does
support Caller ID and FXO, CallManager only supports it through H323
signaling. Also be sure that your FXO port has the "caller-id enable"
config on it.
Mark Snow
Sr Technical Instructor
IPexpert, Inc.
Sent from my iPhone
On Jul 29, 2007, at 7:00 AM, "viny gm" wrote:
> Hi,
>
>
>
> I am getting a problem regarding caller id my FXO port is not
> forwarding the
> caller id to IP phone. When I am using same phone line with analog
> phone the
> caller id is coming on that
>
>
>
> Can any body help on this regards
>
>
>
> Viny
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Sat Aug 18 2007 - 08:17:42 ART