From: Antonio Soares (amsoares@netcabo.pt)
Date: Thu Jul 05 2007 - 16:14:05 ART
Have you tried to enable pim on the loopback interfaces ?
Have you checked IGP connectivity between the loopbacks ?
Do you have ip multicast-routing enabled on both routers ?
R4 and R5 are seeing each other as PIM neighbors ?
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
wim.depauw@getronics.com
Sent: quinta-feira, 5 de Julho de 2007 19:49
To: ccielab@groupstudy.com
Subject: BSR Configuration
Hi,
I'm wrestling with a simple BSR configuration :
I created the following network
R1----FR-----R4----HDLC-----R5----ETH----E2
|--------------------FR------------------ |
I configured R4 & R5 with BSR configuration but when I do a debug they
don't seem to see each other messages
Config R4
Rack1R4#sho run int s1/1
Building configuration...
!
interface Loopback0
ip address 4.4.4.4 255.255.255.255
!
Current configuration : 158 bytes
!
interface Serial1/1
ip address 172.16.2.4 255.255.255.0
ip pim sparse-mode
serial restart-delay 0
clockrate 2016000
no dce-terminal-timing-enable
end
!
!
!
!
Rack1R4#
*Mar 1 01:43:06.671: PIM-BSR(0): bootstrap on non-RPF path Serial1/1
Rack1R4#
*Mar 1 01:43:16.715: PIM-BSR(0): bootstrap on non-RPF path Serial1/0
Rack1R4#
*Mar 1 01:43:37.891: PIM-BSR(0): Build v2 Candidate-RP advertisement for
4.4.4.
4 priority 0, holdtime 210
*Mar 1 01:43:37.895: PIM-BSR(0): Candidate RP's group prefix 224.0.0.0/4
*Mar 1 01:43:37.899: PIM-BSR(0): Send Candidate RP Advertisement to 4.4.4.4
*Mar 1 01:43:37.911: PIM-BSR(0): RP 4.4.4.4, 1 Group Prefixes, Priority 0,
Hol
dtime 210
!
Config R5
Rack1R5#sho run int lo0
Building configuration...
Current configuration : 63 bytes
!
interface Loopback0
ip address 5.5.5.5 255.255.255.255
end
Rack1R5#sho run int s1/1
Building configuration...
Current configuration : 139 bytes
!
interface Serial1/1
ip address 172.16.2.5 255.255.255.0
ip pim sparse-mode
serial restart-delay 0
no dce-terminal-timing-enable
end
!
!
!
Rack1R5#
*Mar 1 01:43:09.047: PIM-BSR(0): RP-set for 224.0.0.0/4
*Mar 1 01:43:09.051: PIM-BSR(0): RP(1) 5.5.5.5, holdtime 210 sec priority
0
*Mar 1 01:43:09.055: PIM-BSR(0): Bootstrap message for 5.5.5.5 originated
Rack1R5#
*Mar 1 01:43:47.195: PIM-BSR(0): Build v2 Candidate-RP advertisement for
5.5.5.
5 priority 0, holdtime 210
*Mar 1 01:43:47.199: PIM-BSR(0): Candidate RP's group prefix 224.0.0.0/4
*Mar 1 01:43:47.203: PIM-BSR(0): Send Candidate RP Advertisement to 5.5.5.5
*Mar 1 01:43:47.215: PIM-BSR(0): RP 5.5.5.5, 1 Group Prefixes, Priority 0,
Hol
dtime 210
Rack1R5#
Does anybody have an idea ? OSPF & connectivity is ok ...
gr
wim
This archive was generated by hypermail 2.1.4 : Sat Aug 18 2007 - 08:17:39 ART