From: Darby Weaver (darbyweaver@yahoo.com)
Date: Sat Jun 09 2007 - 13:27:24 ART
How did you know I am a poor typist... too many typos
here on GS I suppose?
--- Narbik Kocharians <narbikk@gmail.com> wrote:
> That would be a good typing test, its sure improve
> your typing.
>
>
> On 6/9/07, Brian Dennis
> <bdennis@internetworkexpert.com> wrote:
> >
> > If you have a value of 5 seconds you'll need to
> round it up to 1 minute
> > for
> > the absolute-timeout command. Also it'll generate
> a warning message by
> > default before it logs you out.
> >
> > --
> >
> > Brian Dennis, CCIE4 #2210
> (R&S/ISP-Dial/Security/SP)
> > bdennis@internetworkexpert.com
> >
> > Internetwork Expert, Inc.
> > http://www.InternetworkExpert.com
> > Toll Free: 877-224-8987
> > Direct: 775-745-6404 (Outside the US and Canada)
> >
> >
> >
> >
> > On 6/9/07 7:35 AM, "Darby Weaver"
> <darbyweaver@yahoo.com> wrote:
> >
> > > Imagine if you had to troubleshoot this one and
> it was
> > > set to say 5 seconds?
> > >
> > > Interesting.
> > > --- Brian Dennis
> <bdennis@internetworkexpert.com>
> > > wrote:
> > >
> > >> Victor,
> > >> That command is used to determine how long a
> TCP
> > >> session will wait to reach
> > >> the established state. The question was in
> regards
> > >> to how to close a telnet
> > >> session using an absolute timeout. The command
> is
> > >> "absolute-timeout
> > >> <seconds>" under the line configuration.
> > >>
> > >> HTH,
> > >>
> > >> Brian Dennis, CCIE4 #2210
> (R&S/ISP-Dial/Security/SP)
> > >> bdennis@internetworkexpert.com
> > >>
> > >> Internetwork Expert, Inc.
> > >> http://www.InternetworkExpert.com
> > >> Toll Free: 877-224-8987
> > >> Direct: 775-745-6404 (Outside the US and
> Canada)
> > >>
> > >>
> > >>
> > >>
> > >> On 6/8/07 4:46 PM, "Victor Cappuccio"
> > >> <victor@ccbootcamp.com> wrote:
> > >>
> > >>> Hi,
> > >>>
> > >>> R1(config)#ip tcp synwait-time ?
> > >>> <5-300> Wait time
> > >>>
> > >>>
> > >>> Just put 5
> > >>>
> > >>>
> > >>> thanks,
> > >>> Victor Cappuccio.-
> > >>> - CCSI# 31452
> > >>>
> > >>> Network Learning Inc - A Cisco Sponsored
> > >> Organization (SO) YES! We take
> > >>> Cisco Learning credits!
> > >>> victor@ccbootcamp.com
> > >>> http://www.ccbootcamp.com (Cisco Training and
> > >> Rental Racks)
> > >>> http://www.ccbootcamp.com/groupstudy.html
> > >> (groupstudy member discounts!)
> > >>> Voice: 702-968-5100
> > >>> FAX: 702-446-8012
> > >>>
> > >>>
> > >>>
> > >>> -----Original Message-----
> > >>> From: nobody@groupstudy.com on behalf of Adham
> Ali
> > >>> Sent: Fri 6/8/2007 16:45
> > >>> To: ccielab@groupstudy.com
> > >>> Subject: Telnet Absolute Timeout!
> > >>>
> > >>> Dear All,
> > >>>
> > >>> Does anybody know how can i make a telnet
> > >> session to a router be closed
> > >>> automatically after some seconds (Not minutes)
> and
> > >> the session closure should
> > >>> be done evenif the session isn't idle?!!!
> > >>>
> > >>>
> > >>> Waiting for relies!!
> > >>>
> > >>> Regards,
> > >>> Adham.
> > >>>
> > >>>
> > >>> ---------------------------------
> > >>> No need to miss a message. Get email on-the-go
> > >>> with Yahoo! Mail for Mobile. Get started.
> > >>>
> > >>>
> > >>
> > >
>
This archive was generated by hypermail 2.1.4 : Sun Jul 01 2007 - 17:24:48 ART