From: Sadiq Yakasai (sadiqtanko@gmail.com)
Date: Mon Jun 04 2007 - 18:14:04 ART
hey Isma'il,
Thanks for the reply. Had I seen that error msg and still came out
here to ask the question, I would have been booted out i think ;-)
Thanks anyways, but im due for an image upgrade actually.
Sadiq
On 6/4/07, ismail el-shalh <ishelh_mdsa@yahoo.com> wrote:
> 06:59:29: %OSPF-4-NORTRID: OSPF process 1 cannot start. There must be at least one "up" IP interface, for OSPF to use as router ID
>
> Try to assign at least one ip address to any layer 3 interface.
>
>
>
>
> Ismail El-Shalh :)
> MMR/MDSA
>
>
>
>
> ----- Original Message ----
> From: Sadiq Yakasai <sadiqtanko@gmail.com>
> To: Mark Mckillop (mmckillo) <mmckillo@cisco.com>
> Cc: Shamin <ccie.xpert@gmail.com>; Cisco certification <ccielab@groupstudy.com>
> Sent: Monday, June 4, 2007 10:54:25 PM
> Subject: Re: RIP question
>
> hmmmm, guys,
>
> so, whats the reason i cant enable router ospf on a 3560 switch please?
>
> see dump below:
>
> SW2#conf t
> Enter configuration commands, one per line. End with CNTL/Z.
> SW2(config)#ip routing
> SW2(config)#router ospf 1
> SW2(config)#router rip
> SW2(config-router)#exit
> SW2(config)#router ospf 1
> SW2(config)#router ospf 1
> SW2(config)#
>
>
> Could this be a bug or what? it just wont go into router config mode
> for ospf but it does for rip........
>
> Thanks
>
> On 6/3/07, Sadiq Yakasai <sadiqtanko@gmail.com> wrote:
> > so what does it do instead?
> >
> > could it be a configured alias?
> >
> > On 6/3/07, Mark Mckillop (mmckillo) <mmckillo@cisco.com> wrote:
> > > Try adding a network statement that covers an interface and you might
> > > see it magically appear in the config.
> > >
> > > Mark.
> > >
> > > -----Original Message-----
> > > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> > > Shamin
> > > Sent: 03 June 2007 13:50
> > > To: Cisco certification
> > > Subject: RIP question
> > >
> > > Hi All,
> > >
> > > I have a question regarding rip.
> > > IIs there a way in the ios on routers to disable the command "router
> > > rip"
> > > where in the prompt
> > > does not go into the config-router mode. IP routing is enabled in any
> > > case.
> > > Or to put it in a different way, What would be the reason , when you
> > > enter the "router rip" command in the IOS , it does not go into the
> > > config-router mode even when Ip routing is enabled.
> > >
> > > Regards
> > > Shamin
> > >
> > > _______________________________________________________________________
> > > Subscription information may be found at:
> > > http://www.groupstudy.com/list/CCIELab.html
> > >
> > > _______________________________________________________________________
> > > Subscription information may be found at:
> > > http://www.groupstudy.com/list/CCIELab.html
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
>
>
>
>
>
>
>
> ____________________________________________________________________________________
> Looking for a deal? Find great prices on flights and hotels with Yahoo! FareChase.
> http://farechase.yahoo.com/
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Sun Jul 01 2007 - 17:24:46 ART