From: nhatphuc (nhatphuc@gmail.com)
Date: Wed Mar 07 2007 - 00:30:31 ART
I forget to capture the output.
On 3/7/07, Brian Dennis <bdennis@internetworkexpert.com> wrote:
>
> Can you send the output of the "show frame-relay map" command?
>
> --
>
> Brian Dennis, CCIE4 #2210 (R&S/ISP-Dial/Security/SP)
> bdennis@internetworkexpert.com
>
> Internetwork Expert, Inc.
> http://www.InternetworkExpert.com
> Toll Free: 877-224-8987
> Direct: 775-745-6404 (Outside the US and Canada)
>
>
>
>
> On 3/6/07 11:07 AM, "nhatphuc" <nhatphuc@gmail.com> wrote:
>
> > Thanks for replying, Brian.
> >
> > So you please confirm my answer:
> >
> > My configuration is:
> >
> > int s0
> > no ip address
> > encap frame
> > int s0.1 multipoint
> > ip add....
> > frame interface-dlci 100
> >
> > IP address is assigned to multipoint subint and inverse-arp is left to
> > default (enable)
> > 1. => Router will receive DLCI mapping, but only apply to physical
> > interface?
> > 2. => it appears in show frame map (mapped to physical int)?
> >
> > Thanks
> >
> > On 3/7/07, Brian Dennis <bdennis@internetworkexpert.com> wrote:
> >>
> >> Lets first start off with some general understanding regarding this
> topic:
> >>
> >> 1) The frame-relay inverse-arp command applied to the physical
> interface
> >> is
> >> not inherited by the subinterfaces.
> >>
> >> 2) If you do not have an IP address assigned to the
> interface/subinterface
> >> then it doesn't matter really if you disable inverse-arp or leave it to
> >> the
> >> default.
> >>
> >> 3) DLCIs are learned through LMI and are assigned to the physical
> >> interface
> >> by default. There are two command commonly used to reassign a DLCI to
> a
> >> subinterface. The first command is "frame-relay interface-dlci" and
> >> second
> >> command is "frame-relay map". A multipoint subinterface can use either
> of
> >> the command but a point-to-point subinterface can only use the first
> >> command.
> >>
> >> Now knowing this can you restate your question?
> >>
> >> --
> >>
> >> Brian Dennis, CCIE4 #2210 (R&S/ISP-Dial/Security/SP)
> >> bdennis@internetworkexpert.com
> >>
> >> Internetwork Expert, Inc.
> >> http://www.InternetworkExpert.com
> >> Toll Free: 877-224-8987
> >> Direct: 775-745-6404 (Outside the US and Canada)
> >>
> >>
> >>
> >>
> >> On 3/6/07 9:22 AM, "nhatphuc" <nhatphuc@gmail.com> wrote:
> >>
> >>> Hi Group,
> >>>
> >>> If I configure frame relay multipoint subinterface, I don't disable
> >>> inverse-arp on main interface. Will the unspecified DLCI (not
> specified
> >> in
> >>> frame-relay interface-dlci) appear in frame-relay map command?
> >>>
> >>> Thanks
> >>>
> >>> Phuc
> >>>
> >>>
> _______________________________________________________________________
> >>> Subscription information may be found at:
> >>> http://www.groupstudy.com/list/CCIELab.html
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Sun Apr 01 2007 - 06:35:50 ART