RE: NM card in router appears coorectly in show diag but not in

From: Scott Morris (swm@emanon.com)
Date: Sat Nov 18 2006 - 23:19:32 ART


Or reseating the card? Perhaps different slot? SHOULD work. And it's
being detected.

Paste ALL of the bootup messages as there may be some sort of diag error on
there.

 
Scott Morris, CCIE4 (R&S/ISP-Dial/Security/Service Provider) #4713, JNCIE
#153, CISSP, et al.
CCSI/JNCI-M/JNCI-J
IPExpert VP - Curriculum Development
IPExpert Sr. Technical Instructor
smorris@ipexpert.com
http://www.ipexpert.com
 
 

-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of ccie
anees
Sent: Saturday, November 18, 2006 5:48 PM
To: Richard L. Pickard; ccielab@groupstudy.com
Subject: Re: NM card in router appears coorectly in show diag but not in
show run or show ver

Did you try to reload the router?

"Richard L. Pickard" <nettable_walker@hotmail.com> wrote: Has anyone seen
this before ?
I installed a 4 port ISDN card in a rotuer The card appears in the show diag
& the enable light is light on the router BUT the card is not in the show
run or show ver

CP-HUB-#
CP-HUB-#sh diag 3
Slot 3:
BRI (U) Port adapter, 4 ports
Port adapter is disabled
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware revision 1.0 Board revision E0
Serial number 28368698 Part number 800-01238-06 FRU Part Number NM-4B-U=
Test history 0x0 RMA number 00-00-00 EEPROM format version 1 EEPROM contents
(hex):
0x00: 01 22 01 00 01 B0 DF 3A 50 04 D6 06 00 00 00 00
0x10: 70 00 00 00 02 06 29 17 FF FF FF FF FF FF FF FF
0x20: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x30: FF FF FF FF FF FF FF FF FF FF FF FF

CP-HUB-#
CP-HUB-#
CP-HUB-#
CP-HUB-#sh ver
Cisco IOS Software, 3600 Software (C3640-JK9O3S-M), Version 12.4(10),
RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Wed 16-Aug-06 04:04 by prod_rel_team

ROM: System Bootstrap, Version 11.1(7)AX [kuong (7)AX], EARLY DEPLOYMENT
RELEASE SOFTWARE (fc2)

CP-HUB- uptime is 4 minutes
System returned to ROM by power-on
System image file is "flash:c3640-jk9o3s-mz.124-10.bin"

This product contains cryptographic features and is subject to United States
and local country laws governing import, export, transfer and use. Delivery
of Cisco cryptographic products does not imply third-party authority to
import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for compliance
with U.S. and local country laws. By using this product you agree to comply
with applicable laws and regulations. If you are unable to comply with U.S.
and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found
at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

Cisco 3640 (R4700) processor (revision 0x00) with 124928K/6144K bytes of
memory.
Processor board ID 07011222
R4700 CPU at 100MHz, Implementation 33, Rev 1.0
6 Ethernet interfaces
2 Serial interfaces
8 Low-speed serial(sync/async) interfaces DRAM configuration is 64 bits wide
with parity disabled.
125K bytes of NVRAM.
32768K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

CP-HUB-#
CP-HUB-#
CP-HUB-#
CP-HUB-#
CP-HUB-#

CP-HUB-#
CP-HUB-#
CP-HUB-#sh diag 3
Slot 3:
BRI (U) Port adapter, 4 ports
Port adapter is disabled
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware revision 1.0 Board revision E0
Serial number 28368698 Part number 800-01238-06 FRU Part Number NM-4B-U=
Test history 0x0 RMA number 00-00-00 EEPROM format version 1 EEPROM contents
(hex):
0x00: 01 22 01 00 01 B0 DF 3A 50 04 D6 06 00 00 00 00
0x10: 70 00 00 00 02 06 29 17 FF FF FF FF FF FF FF FF
0x20: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x30: FF FF FF FF FF FF FF FF FF FF FF FF

CP-HUB-#
CP-HUB-#
CP-HUB-#
CP-HUB-#sh ver
Cisco IOS Software, 3600 Software (C3640-JK9O3S-M), Version 12.4(10),
RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Wed 16-Aug-06 04:04 by prod_rel_team

ROM: System Bootstrap, Version 11.1(7)AX [kuong (7)AX], EARLY DEPLOYMENT
RELEASE SOFTWARE (fc2)

CP-HUB- uptime is 4 minutes
System returned to ROM by power-on
System image file is "flash:c3640-jk9o3s-mz.124-10.bin"

This product contains cryptographic features and is subject to United States
and local country laws governing import, export, transfer and use. Delivery
of Cisco cryptographic products does not imply third-party authority to
import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for compliance
with U.S. and local country laws. By using this product you agree to comply
with applicable laws and regulations. If you are unable to comply with U.S.
and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found
at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

Cisco 3640 (R4700) processor (revision 0x00) with 124928K/6144K bytes of
memory.
Processor board ID 07011222
R4700 CPU at 100MHz, Implementation 33, Rev 1.0
6 Ethernet interfaces
2 Serial interfaces
8 Low-speed serial(sync/async) interfaces DRAM configuration is 64 bits wide
with parity disabled.
125K bytes of NVRAM.
32768K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

CP-HUB-#
CP-HUB-#
CP-HUB-#
CP-HUB-#
CP-HUB-#



This archive was generated by hypermail 2.1.4 : Fri Dec 01 2006 - 08:05:47 ART