NM card in router appears coorectly in show diag but not in

From: Richard L. Pickard (nettable_walker@hotmail.com)
Date: Sat Nov 18 2006 - 18:54:14 ART

Next message: ccie anees: "Re: NM card in router appears coorectly in show diag but not in"
Previous message: Michael Stout: "RE: tunn mode gre ipv6"
Next in thread: ccie anees: "Re: NM card in router appears coorectly in show diag but not in"
Maybe reply: ccie anees: "Re: NM card in router appears coorectly in show diag but not in"
Maybe reply: Scott Morris: "RE: NM card in router appears coorectly in show diag but not in"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ] [ attachment ]

Has anyone seen this before ?
I installed a 4 port ISDN card in a rotuer
The card appears in the show diag & the enable light is light on the router
BUT the card is not in the show run or show ver

CP-HUB-#
CP-HUB-#sh diag 3
Slot 3:
        BRI (U) Port adapter, 4 ports
        Port adapter is disabled
        Port adapter insertion time unknown
        EEPROM contents at hardware discovery:
        Hardware revision 1.0 Board revision E0
        Serial number 28368698 Part number 800-01238-06
        FRU Part Number NM-4B-U=
        Test history 0x0 RMA number 00-00-00
        EEPROM format version 1
        EEPROM contents (hex):
          0x00: 01 22 01 00 01 B0 DF 3A 50 04 D6 06 00 00 00 00
          0x10: 70 00 00 00 02 06 29 17 FF FF FF FF FF FF FF FF
          0x20: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x30: FF FF FF FF FF FF FF FF FF FF FF FF

CP-HUB-#
CP-HUB-#
CP-HUB-#
CP-HUB-#sh ver
Cisco IOS Software, 3600 Software (C3640-JK9O3S-M), Version 12.4(10),
RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Wed 16-Aug-06 04:04 by prod_rel_team

ROM: System Bootstrap, Version 11.1(7)AX [kuong (7)AX], EARLY DEPLOYMENT
RELEASE SOFTWARE (fc2)

CP-HUB- uptime is 4 minutes
System returned to ROM by power-on
System image file is "flash:c3640-jk9o3s-mz.124-10.bin"

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found
at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

Cisco 3640 (R4700) processor (revision 0x00) with 124928K/6144K bytes of
memory.
Processor board ID 07011222
R4700 CPU at 100MHz, Implementation 33, Rev 1.0
6 Ethernet interfaces
2 Serial interfaces
8 Low-speed serial(sync/async) interfaces
DRAM configuration is 64 bits wide with parity disabled.
125K bytes of NVRAM.
32768K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

CP-HUB-#
CP-HUB-#
CP-HUB-#
CP-HUB-#
CP-HUB-#

CP-HUB-#
CP-HUB-#
CP-HUB-#sh diag 3
Slot 3:
        BRI (U) Port adapter, 4 ports
        Port adapter is disabled
        Port adapter insertion time unknown
        EEPROM contents at hardware discovery:
        Hardware revision 1.0 Board revision E0
        Serial number 28368698 Part number 800-01238-06
        FRU Part Number NM-4B-U=
        Test history 0x0 RMA number 00-00-00
        EEPROM format version 1
        EEPROM contents (hex):
          0x00: 01 22 01 00 01 B0 DF 3A 50 04 D6 06 00 00 00 00
          0x10: 70 00 00 00 02 06 29 17 FF FF FF FF FF FF FF FF
          0x20: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x30: FF FF FF FF FF FF FF FF FF FF FF FF