From: Venkatesh Venkatesh (kvpalani@gmail.com)
Date: Fri Nov 17 2006 - 14:33:08 ART
how abt using vlan filter something like below ?
vlan access-map test 1
action forward
match mac address mac-list
match ip address 10
- Venkatesh
On 11/17/06, Ivan <ivan@iip.net> wrote:
>
> No !
>
> Packet must be matched IP AND MAC.
> For example:
> HOST A
> IP: 1.1.1.1
> MAC: 1.1.1
> HOST B
> IP: 2.2.2.2
> MAC: 2.2.2
>
> acess-list 100 permit host 1.1.1.1 any
> acess-list 100 permit host 2.2.2.2 any
> access-list 1100 permit 1.1.1 0000.0000.0000 0.0.0 ffff.ffff.ffff
> access-list 1100 permit 2.2.2 0000.0000.0000 0.0.0 ffff.ffff.ffff
>
> in such config HOST A can have MAC 2.2.2
>
>
> May be something like that ?????
>
> Giga-LPI(config)#class-map match-all CLASS
> Giga-LPI(config-cmap)#match access-group 100
> Giga-LPI(config-cmap)#match access-group 1100
> Giga-LPI(config-cmap)#policy-map POL
> Giga-LPI(config-pmap)#class CLASS
> Giga-LPI(config-pmap-c)#rat
> Giga-LPI(config-pmap-c)#pol
> Giga-LPI(config-pmap-c)#police 8000 8000 exc
> Giga-LPI(config-pmap-c)#police 8000 8000 exceed-action dro
> Giga-LPI(config-pmap-c)#police 8000 8000 exceed-action drop
> Giga-LPI(config-pmap-c)#
> 01:18:31: %QM-4-CLASS_NOT_SUPPORTED: Classification is not supported in
> classmap CLASS
>
>
>
> On Friday 17 November 2006 18:53, Alexei Monastyrnyi wrote:
> > should this work?
> >
> > SW1(config-cmap)#do sh run | in class|100|1100
> > class-map match-all test
> > match access-group 100
> > match access-group 1100
> > access-list 100 permit ip host 1.1.1.1 host 2.2.2.2
> > access-list 1100 permit aaaa.aaaa.aaaa 0000.0000.0000 bbbb.bbbb.bbbb
> > 0000.0000.0000
> >
> > SW1(config)#mac acc
> > SW1(config)#mac access-list ?
> > extended Extended Access List
> >
> > SW1(config)#access-list ?
> > <1-99> IP standard access list
> > <100-199> IP extended access list
> > _* <1100-1199> Extended 48-bit MAC address access list*_
> > <1300-1999> IP standard access list (expanded range)
> > <200-299> Protocol type-code access list
> > <2000-2699> IP extended access list (expanded range)
> > <700-799> 48-bit MAC address access list
> > dynamic-extended Extend the dynamic ACL absolute timer
> > rate-limit Simple rate-limit specific access list
> >
> > Ivan wrote:
> > > Hello !
> > >
> > > Quick question and short answer.
> > > In production network there is necessity to permit (in|out) packet
> ONLY
> > > if they match IP and MAC address. Can this be achieved with
> Catalyst3550
> > > / Catalyst3750 ?
> > >
> > > To my knowledge mac-ACL match only non-IP traffic. If so, the previous
> > > requirement is not possible.
>
> --
> Ivan
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Fri Dec 01 2006 - 08:05:47 ART