From: david robin (robindavi@gmail.com)
Date: Tue Nov 14 2006 - 06:45:58 ART
yep,
that's right and i think default is the half cir configured but I m still
confused about the frame relay RTP priority + prioirity command Found in the
same class map.
did the sum must be equal to the mincir configured or not, as on my
configuration it accept the values with no problem
thanks a lot
On 11/14/06, Brian Dennis <bdennis@internetworkexpert.com> wrote:
>
> Actually it's minCIR and not CIR when using legacy FRTS. See below:
>
> class-map match-all MY_CLASS
> match any
> !
> policy-map MY_MAP
> class MY_CLASS
> bandwidth percent 100
> !
> interface Serial0/0
> encapsulation frame-relay
> frame-relay traffic-shaping
> frame-relay interface-dlci 102
> class FR_MAP
> !
> map-class frame-relay FR_MAP
> frame-relay cir 512000
> service-policy output MY_MAP
> !
>
> R1(config-map-class)#do sho policy-map int s0/0 | include Band
> Bandwidth 100 (%)
> Bandwidth 256 (kbps) Max Threshold 64 (packets)
> R1(config-map-class)#
> R1(config-map-class)#frame-relay cir 256000
> R1(config-map-class)#
> R1(config-map-class)#do sho policy-map int s0/0 | include Band
> Bandwidth 100 (%)
> Bandwidth 128 (kbps) Max Threshold 64 (packets)
> R1(config-map-class)#
>
> Also you can find this documented on CCO (somewhere ;-)
>
> HTH,
>
> Brian Dennis, CCIE #2210 (R&S/ISP-Dial/Security)
> bdennis@internetworkexpert.com
>
> Internetwork Expert, Inc.
> http://www.InternetworkExpert.com
> Toll Free: 877-224-8987
> Direct: 775-745-6404 (Outside the US and Canada)
>
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> Michael Zuo
> Sent: Monday, November 13, 2006 5:28 PM
> To: Alexey Tolstenok; david robin
> Cc: Cisco certification
> Subject: RE: frame relay rtp priority and priority command ( IWEB LAB 13
> task 8.5)
>
> I agree...
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> Alexey Tolstenok
> Sent: Sunday, November 12, 2006 6:02 AM
> To: david robin
> Cc: Cisco certification
> Subject: Re: frame relay rtp priority and priority command ( IWEB LAB 13
> task 8.5)
>
> I think CBWFQ bandwith limit calculation here is based on "bandwidth"
> command of the main interface or its default value (but not on
> frame-relay
> cir)
>
> Any other opinions?
>
> --
> SY, Alexey
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Fri Dec 01 2006 - 08:05:46 ART