From: Josh Wisman (jwisman@gmail.com)
Date: Sun Nov 12 2006 - 19:20:14 ART
Thank you thats what I thought... I have some example labs that claimed that
you could. It listed "no frame-relay inverse-arp" under each of the
subinterfaces.
On 11/12/06, Elias Chari <elias.chari@gmail.com> wrote:
>
> p-2-p FR subinterfaces do not do in-arp. They will reply to an inverse-arp
> requests from a remote router but will not send in-arp requests.
>
> Think about it this way. A p-2-p interface does not need to do protocol
> resolution. It can only send the traffic to its assigned pvc.
>
> HTH
> Elias
>
>
> On 11/12/06, Josh Wisman <jwisman@gmail.com> wrote:
>
> > Hello everyone. I have a problem I can't figure out. Why can't I add the
> > "no
> > frame-relay inverse-arp" command to a point to point sub interface. It
> > accepts the command but it never shows up in the running config. If I
> > put it
> > on the main interface it will take it and it shows up there... Here is
> > my
> > running config and show ver. I am using dynamips BTW
> >
> >
> > version 12.4
> > service timestamps debug datetime msec
> > service timestamps log datetime msec
> > no service password-encryption
> > !
> > hostname r1
> > !
> > boot-start-marker
> > boot-end-marker
> > !
> > logging console alerts
> > !
> > no aaa new-model
> > memory-size iomem 5
> > !
> > !
> > ip cef
> > !
> > interface Serial1/0
> > no ip address <-------------------- I can insert it here and it will
> > show
> > up
> > encapsulation frame-relay
> > shutdown
> > serial restart-delay 0
> > !
> > interface Serial1/0.1 point-to-point
> > ip address 121.1.12.1 255.255.255.0
> > frame-relay interface-dlci 102
> > !
> > interface Serial1/0.3 point-to-point
> > ip address 121.1.13.1 255.255.255.0 <---------------------Trying to
> > insert
> > it below this line...
> > frame-relay interface-dlci 103
> > !
> > interface Serial1/0.4 point-to-point
> > ip address 121.1.14.1 255.255.255.0
> > frame-relay interface-dlci 104
> > !
> > interface Serial1/1
> > no ip address
> > shutdown
> > serial restart-delay 0
> > !
> > interface Serial1/2
> > no ip address
> > shutdown
> > serial restart-delay 0
> > !
> > interface Serial1/3
> > no ip address
> > shutdown
> > serial restart-delay 0
> > !
> > ip http server
> > !
> > !
> > !
> > !
> > !
> > !
> > control-plane
> > !
> > !
> > !
> > !
> > !
> > !
> > !
> > !
> > !
> > line con 0
> > exec-timeout 60 0
> > line aux 0
> > line vty 0 4
> > !
> > !
> > end
> >
> >
> > r1#show ver
> > Cisco IOS Software, 3600 Software (C3640-JS-M), Version 12.4(10a),
> > RELEASE
> > SOFTW ARE (fc2)
> > Technical Support: http://www.cisco.com/techsupport
> > Copyright (c) 1986-2006 by Cisco Systems, Inc.
> > Compiled Wed 11-Oct-06 20:52 by prod_rel_team
> >
> > ROM: ROMMON Emulation Microcode
> > ROM: 3600 Software (C3640-JS-M), Version 12.4(10a), RELEASE SOFTWARE
> > (fc2)
> >
> > r1 uptime is 30 minutes
> > System returned to ROM by unknown reload cause - suspect
> > boot_data[BOOT_COUNT] 0 x0, BOOT_COUNT 0, BOOTDATA 19
> > System image file is "tftp://255.255.255.255/unknown"
> >
> > Cisco 3640 (R4700) processor (revision 0xFF) with 124928K/6144K bytes of
> > memory.
> > Processor board ID 00000000
> > R4700 CPU at 100MHz, Implementation 33, Rev 1.2
> > 4 Serial interfaces
> > DRAM configuration is 64 bits wide with parity enabled.
> > 125K bytes of NVRAM.
> > 8192K bytes of processor board System flash (Read/Write)
> >
> > Configuration register is 0x40 (will be 0xFFBF at next reload)
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Fri Dec 01 2006 - 08:05:46 ART