From: Brian Dennis (bdennis@internetworkexpert.com)
Date: Wed Nov 08 2006 - 22:38:34 ART
Works fine for me.
BB1-FRS(config)#int lo 0
BB1-FRS(config-if)#ipv6 ospf 1 area 0
BB1-FRS(config-if)#ipv6 add 2001:1::1/64
BB1-FRS(config-if)#ipv6 ospf 1 area 0
BB1-FRS(config-if)#ipv6 ospf network point-to-point
BB1-FRS(config-if)#
BB1-FRS(config)#ipv6 unicast-routing
BB1-FRS(config)#ipv6 router ospf 1
BB1-FRS(config-rtr)#?
area OSPF area parameters
auto-cost Calculate OSPF interface cost according to
bandwidth
compatible OSPF compatibility list
default Set a command to its defaults
default-information Distribution of default information
default-metric Set metric of redistributed routes
discard-route Enable or disable discard-route installation
distance Administrative distance
distribute-list Filter networks in routing updates
exit Exit from IPv6 routing protocol configuration
mode
ignore Do not complain about specific event
log-adjacency-changes Log changes in adjacency state
maximum-paths Forward packets over multiple paths
no Negate a command or set its defaults
passive-interface Suppress routing updates on an interface
redistribute Redistribute IPv6 prefixes from another routing
protocol
router-id router-id for this OSPF process
summary-prefix Configure IPv6 summary prefix
timers Adjust routing timers
BB1-FRS(config-rtr)#
HTH,
Brian Dennis, CCIE #2210 (R&S/ISP-Dial/Security)
bdennis@internetworkexpert.com
Internetwork Expert, Inc.
http://www.InternetworkExpert.com
Toll Free: 877-224-8987
Direct: 775-745-6404 (Outside the US and Canada)
-----Original Message-----
From: Gavin Lawson [mailto:GavinL@titan.net.au]
Sent: Wednesday, November 08, 2006 5:23 PM
To: Brian Dennis; ccielab@groupstudy.com
Subject: RE: OSPF v3 for 2500's
Thanks Brian
But can you confirm that after typing "ipv6 router ospf 1" you go can
enter OSPFv3 sub commands?
I can't
R2-2001#sho ver | in flash:
System image file is "flash:/c2500-is-l.123-18.bin"
R2-2001#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R2-2001(config)#ipv6 ?
access-list Configure access lists
cef Cisco Express Forwarding for IPv6
hop-limit Configure hop count limit
host Configure static hostnames
icmp Configure ICMP parameters
local Specify local options
neighbor Neighbor
prefix-list Build a prefix list
route Configure static routes
router Enable an IPV6 routing process
source-route Process packets with source routing header options
unicast-routing Enable unicast routing
R2-2001(config)#ipv6 router ospf 1
R2-2001(config)#
R2-2001(config)#ipv6 router rip 1
R2-2001(config-rtr)#
GL
-----Original Message-----
From: Brian Dennis [mailto:bdennis@internetworkexpert.com]
Sent: Thursday, 9 November 2006 9:17 AM
To: Gavin Lawson; ccielab@groupstudy.com
Subject: RE: OSPF v3 for 2500's
BB1-FRS#sho ver | in flash:
System image file is "flash:c2500-is-l.122-15.T17.bin"
BB1-FRS#conf t
BB1-FRS(config)#ipv6 ?
access-list Configure access lists
cef Cisco Express Forwarding for IPv6
hop-limit Configure hop count limit
host Configure static hostnames
icmp Configure ICMP parameters
local Specify local options
neighbor Neighbor
ospf OSPF
prefix-list Build a prefix list
route Configure static routes
router Enable an IPV6 routing process
source-route Process packets with source routing header options
unicast-routing Enable unicast routing
HTH,
Brian Dennis, CCIE #2210 (R&S/ISP-Dial/Security)
bdennis@internetworkexpert.com
Internetwork Expert, Inc.
http://www.InternetworkExpert.com
Toll Free: 877-224-8987
Direct: 775-745-6404 (Outside the US and Canada)
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
Gavin Lawson
Sent: Wednesday, November 08, 2006 4:50 PM
To: ccielab@groupstudy.com
Subject: OSPF v3 for 2500's
Does anyone know of an IOS version for 2500's that run OSPFv3
GL
This archive was generated by hypermail 2.1.4 : Fri Dec 01 2006 - 08:05:45 ART