From: Dusty (dustygoody@gmail.com)
Date: Mon Nov 06 2006 - 19:50:29 ART
Make sure switch ports for these interfaces are on same vlan.
On 11/6/06, Capt.Spock <capt.spock@gmail.com> wrote:
>
> > I see that Standby router is unknown in the R2 do sh stand command?
> Looks
> > like R2 is not aware of R1.
> >
> > Can u ping R1 from R2?
> >
> >
> >
> >
> >
> > On 11/6/06, Udo <ccie_groupstudy@yahoo.de> wrote:
> > >
> > > Hi GS,
> > >
> > > I have configured HSRP in my lab.
> > > Here is the config from both routers
> > >
> > > R1
> > >
> > > interface FastEthernet0/0
> > > ip address 192.168.1.1 255.255.255.0
> > > duplex half
> > > standby 1 ip 192.168.1.254
> > > standby 1 priority 50
> > > standby 1 preempt
> > > ================================================
> > > R1(config-if)#do sh stand
> > > FastEthernet0/0 - Group 1
> > > State is Standby
> > > 4 state changes, last state change 00:01:19
> > > Virtual IP address is 192.168.1.254
> > > Active virtual MAC address is 0000.0c07.ac01
> > > Local virtual MAC address is 0000.0c07.ac01 (v1 default)
> > > Hello time 3 sec, hold time 10 sec
> > > Next hello sent in 1.448 secs
> > > Preemption enabled
> > > Active router is 192.168.1.2, priority 100 (expires in 7.412 sec)
> > > Standby router is local
> > > Priority 50 (configured 50)
> > > IP redundancy name is "hsrp-Fa0/0-1" (default)
> > > =======================================
> > >
> > > R2
> > >
> > > interface FastEthernet1/0
> > > ip address 192.168.1.2 255.255.255.0
> > > duplex half
> > > standby 1 ip 192.168.1.254
> > > standby 1 preempt
> > > standby 1 track Serial2/0 100
> > > end
> > > ==================================================
> > >
> > > R2(config-if)#do sh stand
> > > FastEthernet1/0 - Group 1
> > > State is Active
> > > 2 state changes, last state change 00:02:19
> > > Virtual IP address is 192.168.1.254
> > > Active virtual MAC address is 0000.0c07.ac01
> > > Local virtual MAC address is 0000.0c07.ac01 (v1 default)
> > > Hello time 3 sec, hold time 10 sec
> > > Next hello sent in 2.208 secs
> > > Preemption enabled
> > > Active router is local
> > > Standby router is unknown
> > > Priority 100 (default 100)
> > > Track interface Serial2/0 state Up decrement 100
> > > IP redundancy name is "hsrp-Fa1/0-1" (default)
> > >
> > >
> > > In the output you can see that are both routers active even if the R2
> > > S2/0 up or down...
> > > So what happens ?
> > > I think R2 should be the active router until the S2/0 goes down ?! So
> if
> > >
> > > I shutdown the interface nothing happens
> > > But I can see the priority decrements..
> > >
> > > ================================0
> > > R2 after shutdown S2/0
> > >
> > > FastEthernet1/0 - Group 1
> > > State is Active
> > > 2 state changes, last state change 00:10:35
> > > Virtual IP address is 192.168.1.254
> > > Active virtual MAC address is 0000.0c07.ac01
> > > Local virtual MAC address is 0000.0c07.ac01 (v1 default)
> > > Hello time 3 sec, hold time 10 sec
> > > Next hello sent in 1.472 secs
> > > Preemption enabled
> > > Active router is local
> > > Standby router is unknown
> > > >> Priority 0 (default 100)
> > > Track interface Serial2/0 state Down decrement 100
> > > IP redundancy name is "hsrp-Fa1/0-1" (default)
> > >
> > >
> > > Please can anyone explain what is wrong ?
> > >
> > > Thanx
> > >
> > > Udo
> > >
> > >
> > >
> > > ___________________________________________________________
> > > Telefonate ohne weitere Kosten vom PC zum PC:
> http://messenger.yahoo.de
> > >
> > >
> _______________________________________________________________________
> > > Subscription information may be found at:
> > > http://www.groupstudy.com/list/CCIELab.html
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Fri Dec 01 2006 - 08:05:45 ART