From: Brad Ellis (brad@ccbootcamp.com)
Date: Thu Oct 19 2006 - 23:59:38 ART
I'm leaning towards you're SOL and have a bad router.
thanks,
Brad Ellis
CCIE#5796 (R&S / Security)
CCSI#30482
Network Learning Inc - A Cisco Sponsored Organization (SO)
YES! We take Cisco Learning credits!
brad@ccbootcamp.com
www.ccbootcamp.com (Cisco Training and Advanced Technology Rental Racks)
Voice: 702-968-5100
FAX: 702-446-8012
----- Original Message -----
From: "marc fernandez" <mag08036@yahoo.com>
To: "Victor Cappuccio" <cvictor@protokolgroup.com>; <ccielab@groupstudy.com>
Sent: Thursday, October 19, 2006 6:10 PM
Subject: RE: 3640 will not load image [bcc][faked-from]
> OK I tried this. When I remove sticks in bank 2 and 4
> it boots. So what do I do next. Per cisco it mentions
> that to support 128MB you must have bank 0, 1 ,2 ,3
> configured for 32dual = 128mb respectively. Is there a
> certaing configuration I need to do with memory-size
> iomem in order for my router to support 128mb or am I
> out of luck. Help is needed.
>
> -marc
>
> --- Victor Cappuccio <cvictor@protokolgroup.com>
> wrote:
>
>> Yes did you tried this:
>>
>> =======
>>
>> De: nobody@groupstudy.com
>> [mailto:nobody@groupstudy.com] En nombre de Brad
>> Ellis
>> Enviado el: Sabado, 14 de Octubre de 2006 12:38 a.m.
>> Para: marc fernandez; ccielab@groupstudy.com
>> Asunto: Re: 3640 will not load image
>> [bcc][faked-from]
>>
>> I've seen this before...try the following:
>>
>> 1) re-download a very small ip only 3640 image and
>> try that
>> if (1) doesnt work, then (2) try replacing the dram
>> and try the upgrade
>> again
>> if (2) doesnt work, then (3) try replacing the flash
>> (although it doesnt
>> appear to be a flash issue)
>>
>> thanks,
>> Brad Ellis
>> CCIE#5796 (R&S / Security)
>> CCSI#30482
>> Network Learning Inc - A Cisco Sponsored
>> Organization (SO)
>> YES! We take Cisco Learning credits!
>> brad@ccbootcamp.com
>> www.ccbootcamp.com (Cisco Training and Advanced
>> Technology Rental Racks)
>> Voice: 702-968-5100
>> FAX: 702-446-8012
>>
>>
>> -----Mensaje original-----
>> De: marc fernandez [mailto:mag08036@yahoo.com]
>> Enviado el: Sabado, 14 de Octubre de 2006 12:39 p.m.
>> Para: Victor Cappuccio; ccielab@groupstudy.com
>> Asunto: RE: 3640 will not load image
>>
>> Tried all of the steps below. Including output
>> interpretor but I'm still getting the following
>> error
>> after image download. Any comments or ideas on what
>> to
>> do?
>>
>> Error : Uncompression of the image failed.
>> invalid compressed data--format violated
>>
>> Error : zip decompress failed
>>
>> *** System received a Software forced crash ***
>> signal= 0x17, code= 0x7, context= 0x8000eac0
>> PC = 0x800080d4, Cause = 0x20, Status Reg =
>> 0x3041f003
>>
>> -marc
>>
>> --- Victor Cappuccio <cvictor@protokolgroup.com>
>> wrote:
>>
>> > Paste that information in the Cisco Output
>> > interpreter
>> >
>>
> https://www.cisco.com/pcgi-bin/Support/OutputInterpreter/home.pl
>> >
>> > ERROR: A 'Software-forced Crash' error occurs when
>> > the router detects a
>> > severe, unrecoverable error, and reloads itself to
>> > prevent transmission of
>> > corrupt data.
>> >
>> > This error may be caused by watchdog timeouts, low
>> > memory, corrupt software
>> > image,or hardware problems.
>> >
>> > TRY THIS: (please note that there are URLs in the
>> > following text, so go to
>> > OInterpreter Page to check out detail information)
>> >
>> > 1. Please refer to TAC Case Collection -
>> > Software-forced crash for
>> > troubleshooting.
>> > 2. If the "Error : pre and post compression image
>> > sizes disagree" console
>> > message is displayed along with 'Software
>> forced
>> > crash' message, please
>> > refer
>> > to TAC Case Collection - Software-forced crash
>> > (pre and post compression)
>> > for
>> > troubleshooting.
>> > 3. If the "Not enough memory in the system to run
>> > this image" console
>> > message is displayed along with the
>> > 'Software-forced Crash' message,
>> > please refer
>> > to TAC Case Collection - Software-forced crash
>> > (not enough memory) for
>> > troubleshooting.
>> > REFERENCE: For more information, see Understanding
>> > Software-forced Crashes.
>> >
>> > REFERENCE: For more information, see:
>> > Troubleshooting Router Crashes
>> > Less Common Types of System Crashes
>> >
>> >
>> >
>> > -----Mensaje original-----
>> > De: nobody@groupstudy.com
>> > [mailto:nobody@groupstudy.com] En nombre de marc
>> > fernandez
>> > Enviado el: Viernes, 13 de Octubre de 2006 10:40
>> > p.m.
>> > Para: ccielab@groupstudy.com
>> > Asunto: 3640 will not load image
>> >
>> > I have a 3640 which had no mem or flash and would
>> > not
>> > boot. I upgraded it to 128D/32F. Tried to
>> download
>> > flash via xmodem but image still won't load. I now
>> > can
>> > only access it via rommon. Does anyone have any
>> > answers in regards to what I am doing wrong or
>> what
>> > is
>> > wrong? below is the constant reboot I get after a
>> > reset as there is no image on the box when I do a
>> > dir.
>> > I need help desperatly.
>> >
>> > rommon 2 > reset
>> >
>> > System Bootstrap, Version 11.1(20)AA2, EARLY
>> > DEPLOYMENT RELEASE SOFTWARE (fc1)
>> > Copyright (c) 1999 by cisco Systems, Inc.
>> > C3600 processor with 131072 Kbytes of main memory
>> > Main memory is configured to 64 bit mode with
>> parity
>> > disabled
>> >
>> > program load complete, entry point: 0x80008000,
>> > size:
>> > 0x1a7a6f8
>> > Self decompressing the image :
>> > Error : Uncompression of the image failed.
>> > invalid compressed data--format violated
>> >
>> > Error : zip decompress failed
>> >
>> > *** System received a Software forced crash ***
>> > signal= 0x17, code= 0x7, context= 0x8000eb40
>> > PC = 0x800080d4, Cause = 0x20, Status Reg =
>> > 0x3041f003
>> >
>> > System Bootstrap, Version 11.1(20)AA2, EARLY
>> > DEPLOYMENT RELEASE SOFTWARE (fc1)
>> > Copyright (c) 1999 by cisco Systems, Inc.
>> > C3600 processor with 131072 Kbytes of main memory
>> > Main memory is configured to 64 bit mode with
>> parity
>> > disabled
>> >
>> > PCMCIA Slot0: No Card Present
>> >
>> > System Bootstrap, Version 11.1(20)AA2, EARLY
>> > DEPLOYMENT RELEASE SOFTWARE (fc1)
>> > Copyright (c) 1999 by cisco Systems, Inc.
>> >
>> >
>> >
>> > -marc
>> >
>> > __________________________________________________
>> > Do You Yahoo!?
>> > Tired of spam? Yahoo! Mail has the best spam
>> > protection around
>> > http://mail.yahoo.com
>> >
>> >
>>
> _______________________________________________________________________
>> > Subscription information may be found at:
>> > http://www.groupstudy.com/list/CCIELab.html
>> >
>> >
>>
> _______________________________________________________________________
>> > Subscription information may be found at:
>> > http://www.groupstudy.com/list/CCIELab.html
>> >
>>
>>
>> __________________________________________________
>> Do You Yahoo!?
>> Tired of spam? Yahoo! Mail has the best spam
>> protection
> === message truncated ===
>
>
> __________________________________________________
> Do You Yahoo!?
> Tired of spam? Yahoo! Mail has the best spam protection around
> http://mail.yahoo.com
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Wed Nov 01 2006 - 07:29:06 ART