From: Dan C (cdan2154@gmail.com)
Date: Sun Oct 15 2006 - 11:14:31 ART
Hi Marc,
Me again, pls have a look at this link, I did notice that on reload you get
signal = 17 error which points to a Watch Dog timeout.
http://www.cisco.com/en/US/products/sw/iosswrel/ps1835/products_tech_note09186a00800f67db.shtml
If this is a new install I would recommend xmodem another image (maybe a
smaller ip only just for testing first ) and see how it goes if still fails
you may need to replace your motherboard....
Cheers,
Dan
On 10/16/06, Dan C <cdan2154@gmail.com> wrote:
>
> Hi Marc,
>
> Try to change the config reg to ignore your existing configs from rommon:
> confreg 0x2142
> reset
> Maybe you have a old config which is causing the image to crash...
>
>
> On 10/15/06, marc fernandez <mag08036@yahoo.com> wrote:
> >
> > I tried everything below. I can see the image on the
> > box and the meminfo shows the correct information. But
> > it still won't boot. Below is the output.
> >
> > rommon 5 > meminfo
> >
> > Main memory size: 128 MB in 64 bit mode.
> > Available main memory starts at 0xa000e000, size
> > 131016KB
> > IO (packet) memory size: 6 percent of main memory.
> > NVRAM size: 128KB
> > rommon 6 > dir flash:
> > File size Checksum File name
> > 6314736 bytes (0x605af0) 0x117c
> > c3640-i-mz.122-37.bin
> >
> > -marc
> >
> > --- Victor Cappuccio <cvictor@protokolgroup.com>
> > wrote:
> >
> > > Yes did you tried this:
> > >
> > > =======
> > >
> > > De: nobody@groupstudy.com
> > > [mailto:nobody@groupstudy.com] En nombre de Brad
> > > Ellis
> > > Enviado el: Sabado, 14 de Octubre de 2006 12:38 a.m.
> > > Para: marc fernandez; ccielab@groupstudy.com
> > > Asunto: Re: 3640 will not load image
> > > [bcc][faked-from]
> > >
> > > I've seen this before...try the following:
> > >
> > > 1) re-download a very small ip only 3640 image and
> > > try that
> > > if (1) doesnt work, then (2) try replacing the dram
> > > and try the upgrade
> > > again
> > > if (2) doesnt work, then (3) try replacing the flash
> > > (although it doesnt
> > > appear to be a flash issue)
> > >
> > > thanks,
> > > Brad Ellis
> > > CCIE#5796 (R&S / Security)
> > > CCSI#30482
> > > Network Learning Inc - A Cisco Sponsored
> > > Organization (SO)
> > > YES! We take Cisco Learning credits!
> > > brad@ccbootcamp.com
> > > www.ccbootcamp.com (Cisco Training and Advanced
> > > Technology Rental Racks)
> > > Voice: 702-968-5100
> > > FAX: 702-446-8012
> > >
> > >
> > > -----Mensaje original-----
> > > De: marc fernandez [mailto: mag08036@yahoo.com]
> > > Enviado el: Sabado, 14 de Octubre de 2006 12:39 p.m.
> > > Para: Victor Cappuccio; ccielab@groupstudy.com
> > > Asunto: RE: 3640 will not load image
> > >
> > > Tried all of the steps below. Including output
> > > interpretor but I'm still getting the following
> > > error
> > > after image download. Any comments or ideas on what
> > > to
> > > do?
> > >
> > > Error : Uncompression of the image failed.
> > > invalid compressed data--format violated
> > >
> > > Error : zip decompress failed
> > >
> > > *** System received a Software forced crash ***
> > > signal= 0x17, code= 0x7, context= 0x8000eac0
> > > PC = 0x800080d4, Cause = 0x20, Status Reg =
> > > 0x3041f003
> > >
> > > -marc
> > >
> > > --- Victor Cappuccio < cvictor@protokolgroup.com>
> > > wrote:
> > >
> > > > Paste that information in the Cisco Output
> > > > interpreter
> > > >
> > >
> > https://www.cisco.com/pcgi-bin/Support/OutputInterpreter/home.pl
> > > >
> > > > ERROR: A 'Software-forced Crash' error occurs when
> > > > the router detects a
> > > > severe, unrecoverable error, and reloads itself to
> > > > prevent transmission of
> > > > corrupt data.
> > > >
> > > > This error may be caused by watchdog timeouts, low
> > > > memory, corrupt software
> > > > image,or hardware problems.
> > > >
> > > > TRY THIS: (please note that there are URLs in the
> > > > following text, so go to
> > > > OInterpreter Page to check out detail information)
> > > >
> > > > 1. Please refer to TAC Case Collection -
> > > > Software-forced crash for
> > > > troubleshooting.
> > > > 2. If the "Error : pre and post compression image
> > > > sizes disagree" console
> > > > message is displayed along with 'Software
> > > forced
> > > > crash' message, please
> > > > refer
> > > > to TAC Case Collection - Software-forced crash
> > > > (pre and post compression)
> > > > for
> > > > troubleshooting.
> > > > 3. If the "Not enough memory in the system to run
> > > > this image" console
> > > > message is displayed along with the
> > > > 'Software-forced Crash' message,
> > > > please refer
> > > > to TAC Case Collection - Software-forced crash
> > > > (not enough memory) for
> > > > troubleshooting.
> > > > REFERENCE: For more information, see Understanding
> > > > Software-forced Crashes.
> > > >
> > > > REFERENCE: For more information, see:
> > > > Troubleshooting Router Crashes
> > > > Less Common Types of System Crashes
> > > >
> > > >
> > > >
> > > > -----Mensaje original-----
> > > > De: nobody@groupstudy.com
> > > > [mailto:nobody@groupstudy.com] En nombre de marc
> > > > fernandez
> > > > Enviado el: Viernes, 13 de Octubre de 2006 10:40
> > > > p.m.
> > > > Para: ccielab@groupstudy.com
> > > > Asunto: 3640 will not load image
> > > >
> > > > I have a 3640 which had no mem or flash and would
> > > > not
> > > > boot. I upgraded it to 128D/32F. Tried to
> > > download
> > > > flash via xmodem but image still won't load. I now
> > > > can
> > > > only access it via rommon. Does anyone have any
> > > > answers in regards to what I am doing wrong or
> > > what
> > > > is
> > > > wrong? below is the constant reboot I get after a
> > > > reset as there is no image on the box when I do a
> > > > dir.
> > > > I need help desperatly.
> > > >
> > > > rommon 2 > reset
> > > >
> > > > System Bootstrap, Version 11.1(20)AA2, EARLY
> > > > DEPLOYMENT RELEASE SOFTWARE (fc1)
> > > > Copyright (c) 1999 by cisco Systems, Inc.
> > > > C3600 processor with 131072 Kbytes of main memory
> > > > Main memory is configured to 64 bit mode with
> > > parity
> > > > disabled
> > > >
> > > > program load complete, entry point: 0x80008000,
> > > > size:
> > > > 0x1a7a6f8
> > > > Self decompressing the image :
> > > > Error : Uncompression of the image failed.
> > > > invalid compressed data--format violated
> > > >
> > > > Error : zip decompress failed
> > > >
> > > > *** System received a Software forced crash ***
> > > > signal= 0x17, code= 0x7, context= 0x8000eb40
> > > > PC = 0x800080d4, Cause = 0x20, Status Reg =
> > > > 0x3041f003
> > > >
> > > > System Bootstrap, Version 11.1(20)AA2, EARLY
> > > > DEPLOYMENT RELEASE SOFTWARE (fc1)
> > > > Copyright (c) 1999 by cisco Systems, Inc.
> > > > C3600 processor with 131072 Kbytes of main memory
> > > > Main memory is configured to 64 bit mode with
> > > parity
> > > > disabled
> > > >
> > > > PCMCIA Slot0: No Card Present
> > > >
> > > > System Bootstrap, Version 11.1(20)AA2, EARLY
> > > > DEPLOYMENT RELEASE SOFTWARE (fc1)
> > > > Copyright (c) 1999 by cisco Systems, Inc.
> > > >
> > > >
> > > >
> > > > -marc
> > > >
> > > > __________________________________________________
> > > > Do You Yahoo!?
> > > > Tired of spam? Yahoo! Mail has the best spam
> > > > protection around
> > > > http://mail.yahoo.com
> > > >
> > > >
> > >
> > _______________________________________________________________________
> > > > Subscription information may be found at:
> > > > http://www.groupstudy.com/list/CCIELab.html
> > > >
> > > >
> > >
> > _______________________________________________________________________
> > > > Subscription information may be found at:
> > > > http://www.groupstudy.com/list/CCIELab.html
> > > >
> > >
> > >
> > > __________________________________________________
> > > Do You Yahoo!?
> > > Tired of spam? Yahoo! Mail has the best spam
> > > protection
> > === message truncated ===
> >
> >
> > __________________________________________________
> > Do You Yahoo!?
> > Tired of spam? Yahoo! Mail has the best spam protection around
> > http://mail.yahoo.com
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Wed Nov 01 2006 - 07:29:05 ART