From: sabrina pittarel (sabri_esame@yahoo.com)
Date: Wed Sep 20 2006 - 01:39:46 ART
Ok,
sorry for the delay...all my adjacency came up after reload...I'm currently running OSPF point to multipoint over the FR.
Since the lineprotocol for s1/0 changed to UP it took around 5 minutes for the adjacencies to form...I got some "authentication mismatch" at the beginning, but it recovered.
Rack1R3#sh ip ospf neighbor
Neighbor ID Pri State Dead Time Address Interface
150.1.4.4 0 FULL/ - - 187.1.134.4 OSPF_VL1
150.1.1.1 0 FULL/ - - 187.1.134.1 OSPF_VL0
150.1.8.8 1 FULL/DR 00:00:37 187.1.38.8 Ethernet0/1
150.1.1.1 0 FULL/ - 00:01:57 187.1.134.1 Serial1/0
150.1.4.4 0 FULL/ - 00:01:58 187.1.134.4 Serial1/0
Rack1R3#
Sabrina
----- Original Message ----
From: sabrina pittarel <sabri_esame@yahoo.com>
To: CCIEin2006 <ciscocciein2006@gmail.com>
Cc: Heiko Liedtke <heiko.liedtke@gmx.net>
Sent: Saturday, September 16, 2006 9:57:36 AM
Subject: Re: Multiple OSPF keys on Hub and Spoke Frame Relay
Sorry,
in my current set up I don't have the topology required to double check this. As soon as I reconfig, I'll give it a try.
Sabrina
----- Original Message ----
From: CCIEin2006 <ciscocciein2006@gmail.com>
To: sabrina pittarel <sabri_esame@yahoo.com>
Cc: Heiko Liedtke <heiko.liedtke@gmx.net>; ccielab@groupstudy.com
Sent: Saturday, September 16, 2006 8:09:11 AM
Subject: Re: Multiple OSPF keys on Hub and Spoke Frame Relay
Hello Sabrina,
Did reloading work?
AFAIK rollover is just a temporary solution for migrating from one key to
another. I think the intent of its design was not to have multiple keys
operating simultenously but I could be wrong.
Anyone else have luck with this scenario and did it survive a reload?
On 9/15/06, sabrina pittarel <sabri_esame@yahoo.com> wrote:
>
> My configuration at the end is no different of what you get when you
> configure one router at the time, it is just the order of operations that
> makes it working right away.
> It has been a while, but I think I did reload my routers and the neighbor
> relationship came up again after a while...
> But let me try again later, I'll let you know for sure
>
> Sabrina
>
>
> ----- Original Message ----
> From: Heiko Liedtke <heiko.liedtke@gmx.net>
> To: sabrina pittarel <sabri_esame@yahoo.com>
> Cc: CCIEin2006 <ciscocciein2006@gmail.com>; Cisco certification <
> ccielab@groupstudy.com>
> Sent: Friday, September 15, 2006 4:11:31 AM
> Subject: Re: Multiple OSPF keys on Hub and Spoke Frame Relay
>
> I had a similar problem..
>
> When I did a debug ip ospf adj i saw that the router only sends out the
> latest key id. (e.g. sends out
> key 2 and not key 1)
> When I tried do configure the same stuff over an ethernet link, the
> router sends out both keys.
> (key 1 and key 2) Maybe there is a dependency of the ospf network type.
> Can you try to configure an ospf broadcast network type over your frame
> relay cloud?
> Sabrina, what is with your configuration after a reload of the routers??
> I guess this can
> cause problems...
>
> Heiko
>
> I
>
>
>
> sabrina pittarel schrieb:
>
> >This configuration always generates problems (many thread on this in the
> past), but it works. Please looks archives.
> > Try to configure it in this way:
> >
> > * Configure MD5 auth between Hub and Spoke 1 first (no MD5 auth on the
> Hub for Spoke2 yet)
> > * Make sure the neighbor relation ship between Hub and Spoke 1 is fine
> > * Configure MD5 auth between Hub and Spoke 2.
> > * Check the hub is in rollover for the first key you configured
> >
> > Rack1R5#sh ip ospf int s1/0 | b Roll
> > Rollover in progress, 1 neighbor(s) using the old key(s):
> > key id 35
> > Rack1R5#
> >
> >
> > Sabrina
> >
> >----- Original Message ----
> >From: CCIEin2006 <ciscocciein2006@gmail.com>
> >To: Cisco certification <ccielab@groupstudy.com>
> >Sent: Wednesday, September 13, 2006 6:00:59 PM
> >Subject: Multiple OSPF keys on Hub and Spoke Frame Relay
> >
> > This is from IE Vol2 lab 3 task 4.6
> >
> >You have a hub and spoke frame relay using physical interfaces.
> >The task states to use a different OSPF key for each spoke.
> >
> >The solution guide states to configure both keys on the hub with
> different
> >key numbers however when I configure this only one spoke is able to
> >authenticate and the other spoke does not establish adjacency.
> >
> >Here is the setup and solution:
> >
> > R1
> > /
> >R3
> > \
> > R5
> >
> >
> >R1:
> >ip ospf message-digest-key 13 md5 CISCO13
> >R5:
> >ip ospf message-digest-key 35 md5 CISCO35
> >R3: ip ospf message-digest-key 13 md5 CISCO13
> >ip ospf message-digest-key 35 md5 CISCO35
> >
> >As I said only one spoke comes up (I can't remember which and my rack
> time
> >is up).
> >
> >Any ideas are appreciated.
> >
> >_______________________________________________________________________
> >Subscription information may be found at:
> >http://www.groupstudy.com/list/CCIELab.html
> >
> >_______________________________________________________________________
> >Subscription information may be found at:
> >http://www.groupstudy.com/list/CCIELab.html
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Sun Oct 01 2006 - 16:55:41 ART