From: beatccielab (beatccielab@gmail.com)
Date: Fri Sep 01 2006 - 15:47:36 ART
I haven't command max-metric router-lsa at my ospf config..
If i try to issued command : sh ip ospf at R2, i found "Area BACKBONE(0)
(Inactive)".
I try issued command ip ospf prio 0 at serial of R2 and i issued command
"neighb 172.16.1.6" at R5 but this command not working at R5 because not
nbma or point to multipoint..
On 9/2/06, Gianpietro Lavado <gianpietro1@gmail.com> wrote:
>
> I just tried to lab this up, the only scenario in which I did not get the
> VLs to get up was when they had the OSPF cost at 65535. And the only
> scenario where the VLs did not inherit the cost from the interface (
> v.template , physical, etc) and had this 65535 cost was when I had the
> command "max-metric router-lsa" configured, that made the VLs to go down...
> do you have it under your ospf config?
>
> On 9/1/06, beatccielab <beatccielab@gmail.com > wrote:
> >
> > Hi Gianpietro,
> >
> > I already assign diffrent cost but unfortunately virtual link still
> > down..
> > Do you have another something solution?.. Thanks.
> >
> > Rgrds,
> >
> > Beatccielab
> >
> >
> >
> > On 9/1/06, Gianpietro Lavado <gianpietro1@gmail.com > wrote:
> > >
> > > I once had the same problem, it was related to the interface
> > > ospf cost, I beleive you can't build a virtual-link over interfaces with
> > > ospf cost 65535. Try changing it down to any lower value (1 to 65534) on
> > > both sides.
> > >
> > > HTH
> > >
> > > Gianpietro
> > >
> > >
> > > On 9/1/06, beatccielab < beatccielab@gmail.com > wrote:
> > >
> > > > Hi all,
> > >
> > > I have problem with my configuration OSPF virtual link over ppp over
> > > frame
> > > relay..
> > >
> > > Configuration Scenario like this :
> > >
> > > area 0 ---R5--- FRS/area10 --- R2--- area24 ---Cat1
> > >
> > > my case say: R2 not use subinterface..
> > >
> > > i already configure like this :
> > >
> > > R5:
> > > interface Serial0/1/0
> > > no ip address
> > > encapsulation frame-relay
> > > frame-relay interface-dlci 501 ppp Virtual-Template1
> > > no frame-relay inverse-arp
> > > !
> > > interface Virtual-Template1
> > > ip address 172.16.1.5 255.255.255.0
> > >
> > > router ospf 1
> > > router-id 1.1.1.1
> > > area 10 virtual-link 2.2.2.2
> > > network 1.1.1.1 0.0.0.0 area 10
> > > network 172.16.1.5 0.0.0.0 area 10
> > >
> > > R5#sh ip os nei
> > >
> > > Neighbor ID Pri State Dead Time Address
> > > Interface
> > > 2.2.2.2 0 FULL/ - 00:00:38 172.16.1.6
> > > Virtual-Access1
> > >
> > > R5#sh ip os vi
> > > Virtual Link OSPF_VL0 to router 2.2.2.2 is down
> > > Run as demand circuit
> > > DoNotAge LSA allowed.
> > > Transit area 5, Cost of using 65535
> > > Transmit Delay is 1 sec, State DOWN,
> > > Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
> > >
> > >
> > > R6:
> > > interface Serial0/1/0
> > > no ip address
> > > encapsulation frame-relay
> > > frame-relay interface-dlci 105 ppp Virtual-Template1
> > > no frame-relay inverse-arp
> > > !
> > > interface Virtual-Template1
> > > ip address 172.16.1.6 255.255.255.0
> > > !
> > > interface FastEthernet0/0
> > > no ip address
> > > !
> > > interface FastEthernet0/0.24
> > > encapsulation dot1Q 24
> > > ip address 192.1.24.2 255.255.255.0
> > > !
> > > router ospf 1
> > > router-id 2.2.2.2
> > > area 10 virtual-link 1.1.1.1
> > > network 2.2.2.2 0.0.0.0 area 10
> > > network 192.1.24.2 0.0.0.0 area 24
> > > !
> > >
> > > R2#sh ip os vir
> > > Virtual Link OSPF_VL0 to router 1.1.1.1 is down
> > > Run as demand circuit
> > > DoNotAge LSA allowed.
> > > Transit area 5, Cost of using 65535
> > > Transmit Delay is 1 sec, State DOWN,
> > > Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
> > >
> > > R2#sh ip osp nei
> > >
> > > Neighbor ID Pri State Dead Time Address
> > > Interface
> > > 1.1.1.1 0 FULL/ - 00:00:30 172.16.1.5
> > > Virtual-Access1
> > > 3.3.3.3 1 FULL/DR 00:00:35 192.1.24.5
> > > FastEthernet0/0.
> > >
> > >
> > > Cat1
> > >
> > > interface FastEthernet0/1
> > > switchport trunk encapsulation dot1q
> > > switchport trunk allowed vlan 24
> > > switchport mode trunk
> > >
> > > interface Loopback0
> > > ip address 3.3.3.3 255.255.255.0
> > >
> > > interface Vlan13
> > > ip address 192.1.24.5 255.255.255.0
> > >
> > > router ospf 1
> > > router-id 3.3.3.3
> > > log-adjacency-changes
> > > network 3.3.3.3 0.0.0.0 area 24
> > > network 198.1.24.5 0.0.0.0 area 24
> > >
> > >
> > > If issued show ip ospf virtual always down whereas if we issued sh ip
> > > ospf
> > > nei the router another site appears...
> > > Please advice me how to fix it this problem...
> > >
> > > Regards,
> > > beatccielab
> > >
> > > _______________________________________________________________________
> > >
> > > Subscription information may be found at:
> > > http://www.groupstudy.com/list/CCIELab.html
> > >
> > >
> > >
> >
> >
>
-- Regards, beatccielab
This archive was generated by hypermail 2.1.4 : Sun Oct 01 2006 - 16:55:39 ART