From: Victor Cappuccio (cvictor@protokolgroup.com)
Date: Fri Jul 14 2006 - 12:22:35 ART
Try this
On the G0/2
ip address 213.162.233.109 255.255.255.252
ip address 213.162.236.1 255.255.255.240 sec
That should do the trick
-----Mensaje original-----
De: Jens Petter [mailto:jenseike@start.no]
Enviado el: Viernes, 14 de Julio de 2006 11:18 a.m.
Para: 'Victor Cappuccio'
CC: ccielab@groupstudy.com
Asunto: RE: ospf peering
This was the setup :
On router 1 :
interface GigabitEthernet0/2
ip address 213.162.233.109 255.255.255.252 secondary
ip address 213.162.236.1 255.255.255.240
router ospf 1
router-id 213.162.236.1
log-adjacency-changes
passive-interface default
no passive-interface GigabitEthernet0/2
network 213.162.236.0 0.0.0.15 area 0
network 213.162.238.108 0.0.0.3 area 0
default-information originate always
On router 2 :
Interface FastEthernet0/0
Ip address 213.162.233.110 255.255.255.252
router ospf 1
router-id 213.162.233.110
log-adjacency-changes
network 213.162.238.108 0.0.0.3 area 0
The debug said on router 1 :
Jul 14 14:45:26: OSPF: Send hello to 224.0.0.5 area 0 on GigabitEthernet0/2
from 213.162.236.1
Jul 14 14:45:28: OSPF: Rcv pkt from 213.162.233.110, GigabitEthernet0/2,
area 0.0.0.0 : src not on the same network
Then I tried on both routers to set :
Ip ospf network point-to-point
On both interfaces... All connection from router 1 to router two went down
for some reason..? I am not sure what happened there.. This sould not bring
the link down, should it?
-----Original Message-----
From: Victor Cappuccio [mailto:cvictor@protokolgroup.com]
Sent: 14. juli 2006 17:05
To: 'Jens Petter'
Cc: ccielab@groupstudy.com
Subject: RE: ospf peering
The secondary Address is specified in a Network OSPF Command? The OSPF
network command for that secondary address should be in the same area as the
network for the primary address, if not assigned to the same area will not
get advertised
Adjacency will never be formed with an IP Secondary Address.
http://www.juniper.net/techpubs/software/erx/junose61/swconfig-routing-vol1/
html/ospf-config6.html
HTH
Victor.-
-----Mensaje original-----
De: nobody@groupstudy.com [mailto:nobody@groupstudy.com] En nombre de Jens
Petter
Enviado el: Viernes, 14 de Julio de 2006 10:47 a.m.
Para: ccielab@groupstudy.com
Asunto: ospf peering
I am trying to get ospf to peer between two routers... On router 1 I have
enabled ospf for a secondary address on the interface..
The logs say :
Jul 14 14:45:26: OSPF: Send hello to 224.0.0.5 area 0 on GigabitEthernet0/2
from 213.162.236.1
Jul 14 14:45:28: OSPF: Rcv pkt from 213.162.233.110, GigabitEthernet0/2,
area 0.0.0.0 : src not on the same network
Does this mean that it want allow me to peer on secondary addresses?
And, is there a workaround for this?
Jens
This archive was generated by hypermail 2.1.4 : Tue Aug 01 2006 - 07:13:47 ART