From: eicc tester (reto_ccie@yahoo.com)
Date: Mon May 29 2006 - 12:20:55 ART
1)
17:59:05: %STANDBY-3-DUPADDR: Duplicate address 172.16.200.16 on
Vlan200, sourced by 0000.0c07.acc8
you have the same ip addres on 2 vlan interfaces whre you are programing hsrp.
2)
17:59:29: %PM-4-ERR_DISABLE: channel-misconfig error detected on Po1, putting Fa0/1 in err-disable state
17:59:30: %PM-4-ERR_DISABLE: channel-misconfig error detected on Po1, putting Fa0/2 in err-disable state
17:59:30: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down
17:59:31: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down
17:59:31: %LINEPROTO-5-UPDOWN: Line protocol on Interface Port-channel1, changed state to down
17:59:31: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan2, changed state to down
17:59:32: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to down
17:59:32: %LINK-3-UPDOWN: Interface Port-channel1, changed state to down
17:59:32: %LINK-3-UPDOWN: Interface FastEthernet0/2, changed state to down
Is required to see the port-channel interfaces to diagnostics
Ben Malik <souldjab@yahoo.com> wrote: Can someone tell me what I am doing wrong here? I am trying to accomplish lab1 in CCIE practical studies volume2.
Anytime I do the following configuration:
Interface FastEthernet0/1
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 1 mode on
!
interface FastEthernet0/2
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 1 mode on
I get the following errors message:
17:59:05: %STANDBY-3-DUPADDR: Duplicate address 172.16.200.16 on Vlan200, sourced by 0000.0c07.acc8
17:59:29: %PM-4-ERR_DISABLE: channel-misconfig error detected on Po1, putting Fa0/1 in err-disable state
17:59:30: %PM-4-ERR_DISABLE: channel-misconfig error detected on Po1, putting Fa0/2 in err-disable state
17:59:30: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down
17:59:31: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down
17:59:31: %LINEPROTO-5-UPDOWN: Line protocol on Interface Port-channel1, changed state to down
17:59:31: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan2, changed state to down
17:59:32: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to down
17:59:32: %LINK-3-UPDOWN: Interface Port-channel1, changed state to down
17:59:32: %LINK-3-UPDOWN: Interface FastEthernet0/2, changed state to down
I am using one CAT 3550 and 2950.
I shut one port either F0/1 or F0/2 I get no errors and everything work fine.
Any advice will be appreciated.
Thanks,
Soul
---------------------------------
Do you Yahoo!?
Everyone is raving about the all-new Yahoo! Mail Beta.
This archive was generated by hypermail 2.1.4 : Thu Jun 01 2006 - 06:33:22 ART