From: george stanza (cert2006@gmail.com)
Date: Fri May 05 2006 - 11:57:35 ART
Thank you all for your pointers..
On R1, i mapped the LINKLOCAL of R2's Serial and similary on R2, i mapped
the LINKLOCAL of R1..Still no luck...Any idea what i am doing wrong here ?
R1# sh ipv6 int s1 | inc FE80
Serial1 is up, line protocol is up
IPv6 is enabled, link-local address is FE80::209:11FF:FE60:A838
R1(conf-if)# int s1
R1(conf-if)# frame-relay map ipv6 FE80::209:11FF:FE60:A838 112 broadcast
R2# sh ipv6 int s1 | inc FE80
Serial1 is up, line protocol is up
IPv6 is enabled, link-local address is FE80::250:73FF:FED2:3100
R2(conf-if) int s1
R2(conf-if) frame-relay map ipv6 FE80::209:11FF:FE60:A838 211 broadcast
On 5/4/06, Zikopoulos Aristomenis <azik@altec.gr> wrote:
>
> Hello George,
> You can always find the link-local ipv6 address with
> the show ipv6 inter serial 0/0 (example) command :
>
> Router#sh ipv6 inter se 0/0
> Serial0/0 is administratively down, line protocol is down
> IPv6 is enabled, link-local address is FE80::211:93FF:FE50:6040 [TEN]
> Global unicast address(es):
> 2001:CC1E::1, subnet is 2001:CC1E::/64 [TEN]
> Joined group address(es):
> FF02::1
> FF02::1:FF00:1
> FF02::1:FF50:6040
> MTU is 1500 bytes
> ICMP error messages limited to one every 100 milliseconds
> ICMP redirects are enabled
> ND DAD is enabled, number of DAD attempts: 1
> ND reachable time is 30000 milliseconds
>
> The one with the FE80:: format.
>
> Regards,
> Aris
>
>
> -----Original Message-----
> From: nobody@groupstudy.com on behalf of george stanza
> Sent: Fri 5/5/2006 9:26 AM
> To: Cisco certification
> Subject: Ipv6 question !!
>
> R1 & R2 are connected over a frame-relay and i am trying to deploy ipv6
> over
> the FR circuit and configure OSPF between them..i dont see ipv6 OSPF
> sessions coming up though..I believe i need to configure ipv6 link-local
> address but the question says that the ipv6 address should be something
> like
> 2100:0108:122:15::1/64 & 2100:0108:122:15::2/64
>
> R1 Config:
> ========
> ipv6 unicast-routing
> int s1
> ipv6 address 2100:0108:122:15::1/64
> ipv6 enable
> ipv6 ospf 4 area 0
> frame-relay map ipv6 2100:0108:122:15::2 112 broadcast
>
> R2 Config:
> ========
> ipv6 unicast-routing
> int s1
> ipv6 enable
> ipv6 address 2100:0108:122:15::2/64
> ipv6 ospf network point-to-point
> ipv6 ospf 2 area 0
> frame-relay map ipv6 2100:0108:122:15::1 121 broadcast
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Thu Jun 01 2006 - 06:33:20 ART