From: Tony Schaffran (groupstudy@cconlinelabs.com)
Date: Fri Mar 31 2006 - 11:17:12 GMT-3
Actually, it has not been configured as the prompt.
If you look at the output supplied, it looks like the router goes into a
loop.
'Technical Support:' is just part of about the third or fourth line on
reboot.
The first thing I would try is to go into rommon and load another IOS image.
Tony Schaffran
Network Analyst
CCIE #11071
CCNP, CCNA, CCDA,
NNCDS, NNCSS, CNE, MCSE
www.cconlinelabs.com
Your #1 choice for online Cisco rack rentals.
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
Subhash P
Sent: Friday, March 31, 2006 6:06 AM
To: Hash Aminu
Cc: Marc Russell; Cisco certification
Subject: Re: Need Help With My Terminal Server
Hi Hashiru,
I believe that the configuration has been modified to give you the prompt
"Technical Support:"
so please type " configure terminal " at that prompt
and then type " no prompt Technical Support:"
I hope these commands will take you back to your original hostname followed
by the # prompt, viz., " Hisharu#"
Hope this works.
Regards,
Subhash.
On 3/31/06, Hash Aminu <hashng@gmail.com> wrote:
>
> Marc,
> thank you for your response.
> the Issue is that the router does not boot to the command line, it usually
> get stucked @ the Technical Support. Ctrl+C or Ctrl+Z does not work . any
> ideas ?
> TIA
> Hashiru
>
>
> On 3/31/06, Marc Russell <mrussell@ccbootcamp.com> wrote:
> >
> > Get into config mode and type the command below and save.
> >
> >
> > Router(config)#no prompt Technical Support:
> >
> >
> > Marc Russell
> > Network Learning, Inc.
> > Ph# 248-620-9603
> > www.ccbootcamp.com/hardware.html (CCIE practice hardware)
> > www.ccbootcamp.com (CCIE Training)
> >
> >
> >
> > -----Original Message-----
> > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> > Hash
> > Aminu
> > Sent: Friday, March 31, 2006 3:14 AM
> > To: Cisco certification
> > Subject: Need Help With My Terminal Server [bcc][faked-from]
> > Importance: Low
> >
> > Hello GS,
> >
> > I have thi sproblem with my Terminal Server in my Home Lab. Its a 2511
> and
> > anytime i switch it on it came up with a prompt that reads "Techinical
> > Support:"
> > I believed somehow someone know someway outta this Issue because its
> > really
> > preventing me to go on with my Labbing. below is the message its giving
> > me...
> >
> >
> > System Bootstrap, Version 11.0(10c),
> > SOFTWARE
> > Copyright (c) 1986-1996 by cisco
> > Systems
> > 2500 processor with 14336 Kbytes of main memory
> >
> > %SYS-4-CONFIG_NEWER: Configurations from version 12.2 may not be
> correctly
> > under
> >
> > stood.
> > F3: 15535804+889700+1236752 at
> > 0x3000060
> >
> > Restricted Rights Legend
> >
> > Use, duplication, or disclosure by the Government is subject to
> > restrictions
> > as set forth in subparagraph
> > (c) of the Commercial Computer Software - Restric Rights clause at FAR
> > sec.
> > 52.227-19 and subparagraph
> > (c) (1) (ii) of the Rights in Technical Data and Computer Software
> clause
> > at
> > DFARS sec. 252.227-7013.
> >
> >
> > cisco Systems, Inc.
> > 170 West Tasman Drive
> > San Jose, California
> > 95134-1706
> >
> >
> >
> > Cisco Internetwork Operating System
> > Software
> > IOS (tm) 2500 Software (C2500-IS-L), Version 12.2(15)T17, RELEASE
> SOFTWARE
> > (fc1)
> >
> >
> > Technical Support: http://www.cisco.cm/techsupport
> >
> > Copyright (c) 1986-2005 by cisco Systems, Inc.
> > Compiled Sat 13-Aug-05 15:26
> > Image text-base: 0x0308038C, data-base:
> > 0x00001000
> >
> > cisco 2511 (68030) processor (revision M) with 14336K/2048K bytes of
> > memory.
> >
> > Processor board ID 15003458, with hardware revision 00000000 Bridging
> > software.
> > X.25 software, Version 3.0.0.
> > 1 Ethernet/IEEE 802.3 interface(s)
> > 2 Serial network interface(s)
> > 16 terminal line(s)
> > 32K bytes of non-volatile configuration memory.
> > 16384K bytes of processor board System flash (Read ONLY)
> >
> > *Mar 1 00:00:10.983: %LINK-3-UPDOWN: Interface Ethernet0, changed state
> > to
> > up *Mar 1 00:00:10.987: %LINK-3-UPDOWN: Interface Serial0, changed
> state
> > to
> > down *Mar 1 00:00:11.355: %LINK-3-UPDOWN: Interface Serial1, changed
> > state
> > to down *Mar 1 00:00:20.283: %LINEPROTO-5-UPDOWN: Line protocol on
> > Interface Ethernet0, changed state to up *Mar 1 00:00:30.935:
> > %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed
> state
> > to
> > up
> > 00:00:36: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0,
> changed
> > state to down
> > 00:00:38: %LINK-5-CHANGED: Inter~ace Serial0, changed state to
> > administratively down
> > 00:00:40: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1,
> changed
> > state to down
> > 00:00:41: %SYS-5-CONFIG_I: Configured from memory by console
> > (Hashiru's_Termina_
> > Server)
> > 00:01:24: %SYS-5-RESTART: System restarted -- Cisco Internetwork
> Operating
> > System Software IOS (tm) 2500 Software (C2500-IS-L), Version 12.2
> (15)T17,
> > RELEASE SOFTWARE
> > (fc1)
> >
> > Technical Support:
> >
> >
> >
> > Hashiru
> >
> >
> > --
> > B.Eng, MCP,CCNA, CCNP
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
> >
>
>
>
> --
> B.Eng, MCP,CCNA, CCNP
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Sat Apr 01 2006 - 10:07:40 GMT-3