From: Jonathan Stevens (jonathanstevens.net@googlemail.com)
Date: Thu Jan 12 2006 - 19:12:46 GMT-3
So all the roues being learnt by RIP have a next-hop address of loopback 0?
If you change the metric in the first part of the route-map do all the
entries in the routing table change to?
If so, then I guess there may be some bizarre reason why.
Schulz, Dave wrote:
>I have been working on some redistribution in the lab with RIP and
>EIGRP. Here is the scenario....
>
>R1 to R4 running RIP. There is link going to a switch that is running
>EIGRP. I want to redistribute eigrp into rip and also have connected
>routes (loopbacks) redistributed into rip. Here is where it gets a bit
>strange. I understand the issues where we have a protocol redistributed
>into another protocol and also have connected routes being
>redistributed.....however, if I would want to apply different metrics to
>different routes, without using an offset-list. I am not sure that this
>is possible, but would think that it would using the following
>route-map......However, on R1....all the metrics show up as a metric of
>4. Strange? Any thoughts?
>
>Here is the route table on R1....
>
>R1#sh ip rou
>R 4.0.0.0/8 [120/4] via 172.16.14.4, 00:00:18, Serial0/0.14
> 172.16.0.0/24 is subnetted, 2 subnets
>C 172.16.14.0 is directly connected, Serial0/0.14
>C 172.16.123.0 is directly connected, Serial0/0.123
>R 40.0.0.0/8 [120/4] via 172.16.14.4, 00:00:18, Serial0/0.14
>R 41.0.0.0/8 [120/4] via 172.16.14.4, 00:00:18, Serial0/0.14
>
>
>
>R4 config is the key here......
>
>!
>interface Loopback0
> ip address 4.4.4.4 255.255.255.0
>!
>interface Loopback1
> ip address 40.40.40.40 255.255.255.0
>!
>interface Ethernet0
> ip address 41.1.1.1 255.255.255.0
>!
>interface Serial0
> ip address 172.16.14.4 255.255.255.0
> encapsulation frame-relay
> frame-relay map ip 172.16.14.1 401 broadcast
> frame-relay map ip 172.16.14.4 401
> no frame-relay inverse-arp
> frame-relay lmi-type ansi
>!
>!
>router eigrp 100
> network 40.0.0.0
> network 41.0.0.0
> no auto-summary
>!
>router rip
> redistribute connected route-map LOOP
> redistribute eigrp 100 metric 9
> passive-interface default
> network 172.16.0.0
> neighbor 172.16.14.1
> default-metric 1
> no auto-summary
>!
>!
>access-list 1 permit 40.0.0.0 0.255.255.255
>access-list 2 permit 41.1.1.0 0.0.0.255
>!
>route-map LOOP permit 10
> match interface Loopback0
> set metric 4
>!
>route-map LOOP permit 15
> match ip address 1
> set metric 6
>!
>route-map LOOP permit 17
> match ip address 2
> set metric 2
>!
>route-map LOOP permit 20
>!
>!
>
>
>Dave Schulz
>Email: dschulz@dpsciences.com <mailto:dschulz@dpsciences.com >
>
>_______________________________________________________________________
>Subscription information may be found at:
>http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Wed Feb 01 2006 - 07:45:48 GMT-3