From: simon hart (simon@harttel.com)
Date: Tue Oct 04 2005 - 15:43:07 GMT-3
I have not seen the answers to this lab, however you can do this by creating
dialer interfaces on R5. Then one dialer interface will be the backup for a
frame connection, and the other dialer interface can be used for IPv6
connectivity
Simon
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
CCIEBOB
Sent: 04 October 2005 02:44
To: ccielab@groupstudy.com
Subject: Internetwork Expert Lab 2 - 8.5
8.5. Ensure that R5 can trigger an ISDN call to R4 based on any
IPv6 traffic.
I don't think this is possible since the interface has been previously
configured for a backup interface.
Is this correct or is their a way around this?
TIA
R5#ping 2001:CC1E:1:4545::4
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 2001:CC1E:1:4545::4, timeout is 2 seconds:
*Mar 5 00:10:55.820: IPv6: SAS picked source 2001:CC1E:1::5 for
2001:CC1E:1:4545::4 (Loopback0)
*Mar 5 00:10:55.820: IPV6: source 2001:CC1E:1::5 (local)
*Mar 5 00:10:55.820: dest 2001:CC1E:1:4545::4
*Mar 5 00:10:55.824: traffic class 0, flow 0x0, len 100+0, prot 58,
hops 64, Route not found.
*Mar 5 00:10:57.824: IPV6: source 2001:CC1E:1::5 (local)
*Mar 5 00:10:57.824: dest 2001:CC1E:1:4545::4
*Mar 5 00:10:57.824: traffic class 0, flow 0x0, len 100+0, prot 58,
hops 64, Route not found.
*Mar 5 00:10:59.824: IPV6: source 2001:CC1E:1::5 (local)
*Mar 5 00:10:59.824: dest 2001:CC1E:1:4545::4
*Mar 5 00:10:59.824: traffic class 0, flow 0x0, len 100+0, prot 58,
hops 64, Route not found.
*Mar 5 00:11:01.824: IPV6: source 2001:CC1E:1::5 (local)
*Mar 5 00:11:01.824: dest 2001:CC1E:1:4545::4
*Mar 5 00:11:01.824: traffic class 0, flow 0x0, len 100+0, prot 58,
hops 64, Route not found.
*Mar 5 00:11:03.824: IPV6: source 2001:CC1E:1::5 (local)
*Mar 5 00:11:03.824: dest 2001:CC1E:1:4545::4
*Mar 5 00:11:03.824: traffic class 0, flow 0x0, len 100+0, prot 58,
hops 64, Route not found.
Success rate is 0 percent (0/5)
R5#sho ipv6 route
IPv6 Routing Table - 3 entries
Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP
U - Per-user Static route
I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea
O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2
LC 2001:CC1E:1::5/128 [0/0]
via ::, Loopback0
L FE80::/10 [0/0]
via ::, Null0
L FF00::/8 [0/0]
via ::, Null0
R5#sho ipv6 inter brief
FastEthernet0/0 [up/up]
unassigned
Serial0/0 [up/up]
unassigned
Serial0/0.1 [up/up]
unassigned
BRI0/0 [standby mode/down]
FE80::207:EFF:FEBA:E9A0
2001:CC1E:1:4545::5
BRI0/0:1 [administratively down/down]
unassigned
BRI0/0:2 [administratively down/down]
unassigned
FastEthernet0/1 [up/up]
unassigned
Virtual-Access1 [up/up]
unassigned
Loopback0 [up/up]
FE80::207:EFF:FEBA:E9A0
2001:CC1E:1::5
This archive was generated by hypermail 2.1.4 : Sun Nov 06 2005 - 22:00:49 GMT-3