From: Brian Dennis (bdennis@internetworkexpert.com)
Date: Thu Jul 28 2005 - 17:33:39 GMT-3
John,
If you are sure the cable is good then it looks like the ports
are bad. Your only next step is to scratch off the little 2511 on the
back and make it say 2509 ;-)
Brian Dennis, CCIE #2210 (R&S/ISP-Dial/Security)
bdennis@internetworkexpert.com
Internetwork Expert, Inc.
http://www.InternetworkExpert.com
Toll Free: 877-224-8987
Direct: 775-745-6404 (Outside the US and Canada)
-----Original Message-----
From: John Matus [mailto:john_matus@hotmail.com]
Sent: Thursday, July 28, 2005 1:27 PM
To: Brian Dennis; ccielab@groupstudy.com
Subject: RE: 2511 terminal server woes
they all fail to connect.
>From: "Brian Dennis" <bdennis@internetworkexpert.com>
>To: "John Matus" <john_matus@hotmail.com>,<ccielab@groupstudy.com>
>Subject: RE: 2511 terminal server woes
>Date: Thu, 28 Jul 2005 16:12:13 -0400
>
>John,
> Did you try and test every line (9-16)?
>
>Brian Dennis, CCIE #2210 (R&S/ISP-Dial/Security)
>bdennis@internetworkexpert.com
>
>Internetwork Expert, Inc.
>http://www.InternetworkExpert.com
>Toll Free: 877-224-8987
>Direct: 775-745-6404 (Outside the US and Canada)
>
>
>-----Original Message-----
>From: John Matus [mailto:john_matus@hotmail.com]
>Sent: Thursday, July 28, 2005 12:39 PM
>To: Brian Dennis; ccielab@groupstudy.com
>Subject: RE: 2511 terminal server woes
>
>here is the running config and the sh line 1 16.
>
>Terminal># sh line 1 16
> Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise
Overruns
>
>Int
> 1 TTY 9600/9600 - inout - - - 4 0 0/0
>
>-
> 2 TTY 9600/9600 - inout - - - 1 0 0/0
>
>-
> 3 TTY 9600/9600 - inout - - - 0 0 0/0
>
>-
> 4 TTY 9600/9600 - inout - - - 0 0 0/0
>
>-
> 5 TTY 9600/9600 - inout - - - 0 0 0/0
>
>-
> 6 TTY 9600/9600 - inout - - - 0 0 0/0
>
>-
> 7 TTY 9600/9600 - inout - - - 1 0 0/0
>
>-
> 8 TTY 9600/9600 - inout - - - 1 0 0/0
>
>-
> 9 TTY 9600/9600 - inout - - - 4 0 0/0
>
>-
> 10 TTY 9600/9600 - inout - - - 2 0 0/0
>
>-
> 11 TTY 9600/9600 - inout - - - 0 0 0/0
>
>-
> 12 TTY 9600/9600 - inout - - - 0 0 0/0
>
>-
> 13 TTY 9600/9600 - inout - - - 0 0 0/0
>
>-
> 14 TTY 9600/9600 - inout - - - 0 0 0/0
>
>-
> 15 TTY 9600/9600 - inout - - - 0 0 0/0
>
>-
> 16 TTY 9600/9600 - inout - - - 0 0 0/0
>
>-
>
>
>Terminal>#sh run
>Building configuration...
>
>Current configuration : 1461 bytes
>!
>version 12.2
>service timestamps debug datetime msec
>service timestamps log datetime msec
>no service password-encryption
>!
>hostname Terminal>
>!
>logging queue-limit 100
>enable secret 5 $1$Rkh1$gOFBTEytcjnPL.uXWsIre1
>enable password disco
>!
>ip subnet-zero
>no ip routing
>ip host r1 2001 1.1.1.1
>ip host r2 2002 1.1.1.1
>ip host r3 2003 1.1.1.1
>ip host r4 2004 1.1.1.1
>ip host r5 2005 1.1.1.1
>ip host r6 2006 1.1.1.1
>ip host bb1 2007 1.1.1.1
>ip host bb2 2008 1.1.1.1
>ip host bb3 2009 1.1.1.1
>ip host sw1 2010 1.1.1.1
>ip host sw2 2011 1.1.1.1
>ip host frame 2012 1.1.1.1
>!
>!
>!
>!
>interface Loopback0
>ip address 1.1.1.1 255.255.255.255
>!
>interface Ethernet0
>ip address 10.51.16.18 255.255.254.0
>no ip route-cache
>no ip mroute-cache
>!
>interface Serial0
>no ip address
>no ip route-cache
>no ip mroute-cache
>shutdown
>no fair-queue
>!
>interface Serial1
>no ip address
>no ip route-cache
>no ip mroute-cache
>shutdown
>!
>no ip http server
>no ip classless
>!
>!
>!
>!
>alias exec c conf t
>alias exec r1 telnet r1
>alias exec r2 telnet r2
>alias exec r3 telnet r3
>alias exec r4 telnet r4
>alias exec r5 telnet r5
>alias exec r6 telnet r6
>alias exec sw1 telnet sw1
>alias exec sw2 telnet sw2
>alias exec bb1 telnet bb1
>alias exec bb2 telnet bb2
>alias exec bb3 telnet bb3
>alias exec frame telnet frame
>!
>line con 0
>transport output none
>line 1 16
>exec-timeout 5 0
>flush-at-activation
>modem InOut
>no exec
>transport input all
>line aux 0
>line vty 0 4
>password cisco
>login
>!
>end
>
>
>
>
> >From: "Brian Dennis" <bdennis@internetworkexpert.com>
> >To: "John Matus" <john_matus@hotmail.com>,<ccielab@groupstudy.com>
> >Subject: RE: 2511 terminal server woes
> >Date: Thu, 28 Jul 2005 15:19:13 -0400
> >
> >John,
> > The "open" is just saying that the telnet session is connected.
> >Why don't you just post your whole configuration here along with the
> >output of the "show line 1 16" command.
> >
> >Brian Dennis, CCIE #2210 (R&S/ISP-Dial/Security)
> >bdennis@internetworkexpert.com
> >
> >Internetwork Expert, Inc.
> >http://www.InternetworkExpert.com
> >Toll Free: 877-224-8987
> >Direct: 775-745-6404 (Outside the US and Canada)
> >
> >
> >-----Original Message-----
> >From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf
Of
> >John Matus
> >Sent: Thursday, July 28, 2005 12:07 PM
> >To: ccielab@groupstudy.com
> >Subject: 2511 terminal server woes
> >
> >ok,
> >i had a bad cable on this 2511 for ports 9-16 <it has 1 port for 1-8
>and
> >
> >another for 9-16 that use the octal cables>. i replaced the cable
but
> >still am unable to establish a reverse telnet session throught ports
> >9-16
> >when i telnet in i get a status of "open" but i don't seem to
interface
> >w/
> >the router....i just get a blank screen and nothing when i hit enter
a
> >few
> >times. would a bad async port still show connections as being
"open"?
> >it
> >seems like the port is bad but perhaps i'm doing something wrong.
any
> >suggestions?
> >
> >TIA
> >
> >_________________________________________________________________
> >Is your PC infected? Get a FREE online computer virus scan from
McAfee.
> >Security. http://clinic.mcafee.com/clinic/ibuy/campaign.asp?cid=3963
> >
>
>_______________________________________________________________________
> >Subscription information may be found at:
> >http://www.groupstudy.com/list/CCIELab.html
>
>_________________________________________________________________
>Don't just search. Find. Check out the new MSN Search!
>http://search.msn.click-url.com/go/onm00200636ave/direct/01/
>
This archive was generated by hypermail 2.1.4 : Sun Sep 04 2005 - 17:00:31 GMT-3