From: Arun Arumuganainar (aarumuga@hotmail.com)
Date: Thu Jul 28 2005 - 03:03:33 GMT-3
----- Original Message -----
From: gladston@br.ibm.com
To: Bajo
Cc: Arun Arumuganainar ; ccielab@groupstudy.com ; Chris Lewis (chrlewis) ;
san
Sent: Thursday, July 28, 2005 6:46 AM
Subject: Re: Queue with GTS
Thanks,
More clear now.
This is from Wendell:
"In some cases, IOS does not place the packets into a shaping queue as they
arrive, but instead the packets are placed into the Software queue or TX
Queue. When the shaping features knows that a newly arrived packet does not
exceed the shaping rate, there is no need to delay the packet. In that case, a
queuing tool used for managing the shaping queue would also have no effect on
that particular packet. "
[Arun]
This is absolutely true and this is how Shaping works . When a packet
arrives , it will check the token bucket if credit available it will be sent
to Software queue ( or directly to H/W queue if it is not full ) . If credits
are not available then this will be placed in the shapping queue ( Read more
about token bucket algorithm for Details ).
[Arun]
But, could you think about an example using a tool for queue created by
shaping and a tool queue for the main interface used at the same time?
I remember that when we configure fragmentation, IOS creates two queues on
the main interface, and we can still use other tools (LLQ, CQ, PQ, IP RTP
Priority) on the queue created by shaping.
Then, correcting my last post, this would occur:
|shaping queue|------->|software queue|-------->|hardware queue|
LLQ Dual-Fifo
Fifo
[Arun]
See What queueing technique does shaping and software queues uses is
implementation specific .
For Cisco with GTS the scenario look like this
|shaping queue|------->|software queue|-------->|hardware queue|
WFQ CQ or PQ or Fifo Fifo
For Cisco with FRTS th scenario look like this
|shaping queue|------->|software queue|-------->|hardware queue|
CQ or PQ or Fifo WFQ Fifo
Note :LLQ belong to different category . LLQ = Strict Priority Queue +
Policing . An Standalone LLQ can not be used for shapping ( A PQ can be used
instead of this ).
Certainly you can verify this by configuring this in your lab
Hope it is clear now
[Arun]
Any other example besides this one?
Cordially,
------------------------------------------------------------------
Gladston
Bajo <bajoalex@gmail.com>
27/07/2005 21:31 Please respond to
Bajo <bajoalex@gmail.com>
To Alaerte Gladston Vidali/Brazil/IBM@IBMBR
cc san <san.study@gmail.com>, Arun Arumuganainar
<aarumuga@hotmail.com>, ccielab@groupstudy.com, "Chris Lewis (chrlewis)"
<chrlewis@cisco.com>
Subject Re: Queue with GTS
Hi all,
Arun is correct. Take a look at the "Decision Logic for Queuing" in
Wendell Odom's Cisco QoS, 2ed, page 358. Here are some points from the
book ....
Shaping Queues exist separately from the interface software queues ...
After passing any Shaping tool (say PQ...etc), if there is any shaping
applied, packets are sent into Software Queues associated with the
physical interface and then forwarded out the interface.
"If Hardware Queue is not full, packet are immediately placed in
Hardware Queue, bypassing the interface Software Queue....."
On 7/27/05, gladston@br.ibm.com <gladston@br.ibm.com> wrote:
> Hi San,
>
> I hope Arun answers it.
> As I see the process, there is a hardware queue and software queue. I
> don't think it would exist something like this going on:
> |shaping queue|----->|sofware queue|---->|hardware queue|
>
> The shaping queue is itself a software queue.
> Would IOS move from a software queue (called shaping queue) to another
> software queue(called just "software queue")?
>
> Cordially,
> ------------------------------------------------------------------
> Gladston
>
>
>
>
> san <san.study@gmail.com>
> 27/07/2005 12:29
> Please respond to
> san <san.study@gmail.com>
>
>
> To
> Arun Arumuganainar <aarumuga@hotmail.com>
> cc
> Alaerte Gladston Vidali/Brazil/IBM@IBMBR, "Chris Lewis (chrlewis)"
> <chrlewis@cisco.com>, ccielab@groupstudy.com
> Subject
> Re: Queue with GTS
>
>
>
>
>
>
> Hi Arun,
>
> Can you give an example of how to modify a software queue ? Is it by
> the command "fair-queue , no fair-queue" under the interface. I know
> shaping queue can be modified with shapping configurations
> (FRTS/GTS/CBTS).
>
> Dumb Question, If i use shaping, does the software queue is
> overwritten by shapping queue or still packet goes through both the
> queues like below
> PQ with GTS :
> interface serial 0
> priority-group 4 ((priority queue to define software queue))
> traffic-shape rate xxxx (( to create a shapping queue ))
>
>
> /SAN
>
> On 7/27/05, Arun Arumuganainar <aarumuga@hotmail.com> wrote:
> > Actually there are 3 queues in IOS .
> >
> > 1) Hardware Queue :- Single Queue and Always FIFO . We can not do any
> thing
> > about it .
> > 2) Software Queue
> > 3) Shaping Queue ( Will be used only when shaping is turned on ) .
> >
> > How Packets are enqued in Software or Shaping Queue ?
> >
> > Well the answer lies in what kind of traffic shaping you you use Here
> are
> > the details .
> >
> > 1) GTS : Shaping Queue : WFQ only supported . Software Queue : PQ ,
> CQ or
> > FIFO
> > 2) FRTS : Shaping Queue : PQ, CQ and FIFO Software Queue : WFQ only
> > 3) CB-Traffic Shaping : Uses WFQ for both Shaping and Software Queue .
> >
> > Well the " sh interface " o/p tells you only about the software queue
> and
> > "show traffic " will give you about shaping queue .
> >
> > Hope this helps .
> >
> > Thanks and Regards
> > Arun
> > ----- Original Message -----
> > From: <gladston@br.ibm.com>
> > To: "Chris Lewis (chrlewis)" <chrlewis@cisco.com>
> > Cc: <ccielab@groupstudy.com>
> > Sent: Wednesday, July 27, 2005 12:37 AM
> > Subject: RE: Queue with GTS
> >
> >
> > > No, Chris, thanks a lot.
> > >
> > > That is what I was looking for.
> > >
> > > Wendell book confirmed that GTS uses WFQ.
> > >
> > > I read that before, but nothing like practice to memorize.
> > >
> > > Cordially,
> > > ------------------------------------------------------------------
> > > Gladston
> > >
> > >
> > >
> > >
> > > "Chris Lewis \(chrlewis\)" <chrlewis@cisco.com>
> > > 26/07/2005 15:52
> > >
> > > To
> > > Alaerte Gladston Vidali/Brazil/IBM@IBMBR, <ccielab@groupstudy.com>
> > > cc
> > >
> > > Subject
> > > RE: Queue with GTS
> > >
> > >
> > >
> > >
> > >
> > >
> > > Hi Gladston,
> > >
> > > This is how I would read the output.
> > >
> > > GTS acts upon an interface or subinterface. GTS here is configured
for
> a
> > > specific sub-interface and the queue that GTS will build to do
shaping
> > > on will use WFQ. The main interface can have fifo or wfq configured
on
> > > it. Are you looking at something else?
> > >
> > > Chris
> > >
> > > -----Original Message-----
> > > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf
> Of
> > > gladston@br.ibm.com
> > > Sent: Tuesday, July 26, 2005 12:20 PM
> > > To: ccielab@groupstudy.com
> > > Subject: Queue with GTS
> > >
> > > Hi,
> > >
> > > GTS is applyed to interface serial 0/0.14.
> > > 'sh traffic queue' shows that the queue created by GTS uses WFQ.
> > >
> > > It seems it does not matter what is configured on the interface, in
> this
> > > case fifo.
> > >
> > > Would you comment this?
> > >
> > > Rack2R1(config-subif)#do sh traf que
> > > Traffic queued in shaping queue on Serial0/0.14
> > > Queueing strategy: weighted fair
> > > Queueing Stats: 9/1000/64/10026 (size/max total/threshold/drops)
> > > Conversations 2/4/16 (active/max active/max total)
> > > Reserved Conversations 0/0 (allocated/max allocated)
> > > Available Bandwidth 96 kilobits/sec
> > >
> > > (depth/weight/total drops/no-buffer drops/interleaves)
5/32384/380/0/0
> > > Conversation 0, linktype: ip, length: 64
> > > source: 150.100.1.254, destination: 148.5.4.1, id: 0x03F6, ttl: 254,
> > > TOS: 0 prot: 17, source port 55172, destination port 5002
> > >
> > > (depth/weight/total drops/no-buffer drops/interleaves)
5/32384/766/0/0
> > > Conversation 7, linktype: ip, length: 64
> > > source: 150.100.1.254, destination: 148.5.4.1, id: 0x0020, ttl: 254,
> > > TOS: 0 prot: 17, source port 51068, destination port 5001
> > >
> > >
> > > Rack2R1(config-subif)#do sh int ser 0/0
> > > Serial0/0 is up, line protocol is up
> > > Hardware is PowerQUICC Serial
> > > MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,
> > > reliability 255/255, txload 255/255, rxload 10/255
> > > Encapsulation FRAME-RELAY, loopback not set
> > > Keepalive set (10 sec)
> > > LMI enq sent 95, LMI stat recvd 95, LMI upd recvd 0, DTE LMI up
> > > LMI enq recvd 0, LMI stat sent 0, LMI upd sent 0
> > > LMI DLCI 1023 LMI type is CISCO frame relay DTE
> > > FR SVC disabled, LAPF state down
> > > Broadcast queue 0/64, broadcasts sent/dropped 178/0, interface
> > > broadcasts 162
> > > Last input 00:00:01, output 00:00:00, output hang never
> > > Last clearing of "show interface" counters 00:15:49
> > > Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
> > > 10878
> > > Queueing strategy: fifo
> > > Output queue: 0/40 (size/max)
> > > 1 minute input rate 95000 bits/sec, 183 packets/sec
> > > 1 minute output rate 95000 bits/sec, 185 packets/sec
> > > 159447 packets input, 10401005 bytes, 0 no buffer
> > > Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
> > > 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
> > > 163288 packets output, 10609440 bytes, 0 underruns
> > > 0 output errors, 0 collisions, 0 interface resets
> > > 0 output buffer failures, 0 output buffers swapped out
> > > 0 carrier transitions
> > > DCD=up DSR=up DTR=up RTS=up CTS=up
> > >
> > >
> > > This is the config:
> > >
> > > interface Serial0/0.14 point-to-point
> > > bandwidth 128
> > > ip address 148.5.14.1 255.255.255.0
> > > traffic-shape rate 96000 12000 1000 1000 frame-relay interface-dlci
> > > 104
> > >
> > >
> _______________________________________________________________________
> > > Subscription information may be found at:
> > > http://www.groupstudy.com/list/CCIELab.html
> > >
> > >
> _______________________________________________________________________
> > > Subscription information may be found at:
> > > http://www.groupstudy.com/list/CCIELab.html
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
--
Kind Regards,
Bajo
This archive was generated by hypermail 2.1.4 : Sun Sep 04 2005 - 17:00:31 GMT-3