From: istong@stong.org
Date: Sat Jul 23 2005 - 08:22:02 GMT-3
Given that cable a works on 1-8 and not 9-16 tells me there
is something wrong with 9-16 (config or physical port). If
the config for ports 1-8 and 9-16 are the same then you have
a physical interface problem.
Given that cable b does not work on 9-16 or 1-8 (but cable a
does work on 1-8) tells me that cable b is bad and would
need replacing
Thanks,
Ian
http://ccie4u.com
Rack Rentals starting at only $12
> ok, here is where i'm at...just checking in.
>
> first i had a working async 1-8 and a non-working 9-16
> i swapped the cables and then had a non-working 1-8 AND a
> NON-working 9-16. i switched them back and 1-8 is
> working again and 9-16 is dead. is this just a bad
> cable OR a bad cable and a bad 2nd async port?
>
> >From: istong@stong.org
> >Reply-To: istong@stong.org
> >To: "John Matus" <john_matus@hotmail.com>,
> marvin@ccbootcamp.com, >ccielab@groupstudy.com
> >Subject: RE: termal server revese telnet config
> [bcc][faked-from] >Date: Thu, 21 Jul 2005 18:33:28 -0400
> >
> >Has to be the cable that is the issue based on info
> >provided.
> >
> >
> >Ian
> >www.ccie4u.com
> >Rack Rentals starting at only $12
> >
> >
> > > i should have also said that the green light was on
> > > when the cables were reversed (when 1-8 were
> > working). >
> > > >From: marvin greenlee <marvin@ccbootcamp.com>
> > > >To: 'John Matus' <john_matus@hotmail.com>,
> > > ccielab@groupstudy.com >Subject: RE: termal server
> > > revese telnet config [bcc][faked-from] >Date: Thu, 21
> > > Jul 2005 15:20:33 -0700 >
> > > >3 - bad cable
> > > >
> > > >Marvin Greenlee, CCIE#12237, CCSI# 30483
> > > >Network Learning Inc
> > > >marvin@ccbootcamp.com
> > > >www.ccbootcamp.com (Cisco Training)
> > > >
> > > >
> > > >-----Original Message-----
> > > >From: John Matus [mailto:john_matus@hotmail.com]
> > > >Sent: Thursday, July 21, 2005 3:13 PM
> > > >To: john_matus@hotmail.com; marvin greenlee;
> > > ccielab@groupstudy.com >Subject: RE: termal server
> > > revese telnet config [bcc][faked-from] >
> > > >new problem same beast.
> > > >
> > > >the 2511 has 2 octal cables for async ports. ports
> > > 1-8 work fine. ports >9-16 don't work at all. i
> > > swapped the cables and now 1-8 won't work. i'm
> > > >thinking 1 or 2 things. 1) async serial port-bank
> > > 9-16 is bad, or (this is >a stretch). ports 9-16 wont
> > > work unless there is a functional cable on >ports
> > > >
> > > >1-8........?
> > > >
> > > > >From: "John Matus" <john_matus@hotmail.com>
> > > > >Reply-To: "John Matus" <john_matus@hotmail.com>
> > > > >To: marvin@ccbootcamp.com, ccielab@groupstudy.com
> > > > >Subject: RE: termal server revese telnet config
> > > > [bcc][faked-from] >Date: Thu, 21 Jul 2005 20:39:05
> > > > +0000 >
> > > > >ahhhhhhhhhhh. that's the piece of info i
> > > > needed...works great now!!! ;) >
> > > > >>From: marvin greenlee <marvin@ccbootcamp.com>
> > > > >>Reply-To: marvin greenlee <marvin@ccbootcamp.com>
> > > > >>To: "'John Matus'" <john_matus@hotmail.com>,
> > > > ccielab@groupstudy.com >>Subject: RE: termal server
> > > > revese telnet config [bcc][faked-from] >>Date: Thu,
> > > > 21 Jul 2005 13:30:37 -0700 >>
> > > > >>Should have been more clear. Needs to match an
> > > > address locally on the >>term
> > > > >>server.
> > > > >>
> > > > >>Marvin Greenlee, CCIE#12237, CCSI# 30483
> > > > >>Network Learning Inc
> > > > >>marvin@ccbootcamp.com
> > > > >>www.ccbootcamp.com (Cisco Training)
> > > > >>
> > > > >>
> > > > >>-----Original Message-----
> > > > >>From: John Matus [mailto:john_matus@hotmail.com]
> > > > >>Sent: Thursday, July 21, 2005 1:24 PM
> > > > >>To: marvin greenlee; ccielab@groupstudy.com
> > > > >>Subject: RE: termal server revese telnet config
> > > > [bcc][faked-from] >>
> > > > >>ok, i don't understand the ip address part of
> > > this. take for example >the
> > > > >>racks that you rent online. when you log into the
> > > terminal server you >do
> > > > >>a
> > > > >>reverse telnet into say R1. R1 has a completely
> > > > blank configuration (i >>believe), so how can you
> > > > assign the ip address of the ethernet interface >>or
> > > > >>the loopback interface.....and why would you
> > > > assign this when you are >>initiating the session
> > > > through the async ports where (i would think) ip
> > > > >>addresses have no meaning?? :-0 >>
> > > > >> >From: marvin greenlee <marvin@ccbootcamp.com>
> > > > >> >To: 'John Matus' <john_matus@hotmail.com>,
> > > > ccielab@groupstudy.com >> >Subject: RE: termal
> > > > server revese telnet config [bcc][faked-from] >>
> > > > >Date: Thu, 21 Jul 2005 13:23:44 -0700 >> >
> > > > >> >The address needs to match a local address on
> > > > the router (usually >>1.1.1.1
> > > > >> >is
> > > > >> >added as a loopback.)
> > > > >> >
> > > > >> >The other parts are configured under the line 1
> > > > 16. You may also want >>to
> > > > >> >include things such as exec timeouts for the
> > > > lines. >> >
> > > > >> >Marvin Greenlee, CCIE#12237, CCSI# 30483
> > > > >> >Network Learning Inc
> > > > >> >marvin@ccbootcamp.com
> > > > >> >www.ccbootcamp.com (Cisco Training)
> > > > >> >
> > > > >> >
> > > > >> >-----Original Message-----
> > > > >> >From: nobody@groupstudy.com
> > > [mailto:nobody@groupstudy.com] On Behalf >Of
> > > > >> >John
> > > > >> >Matus
> > > > >> >Sent: Thursday, July 21, 2005 1:13 PM
> > > > >> >To: ccielab@groupstudy.com
> > > > >> >Subject: termal server revese telnet config
> > > > [bcc][faked-from] >> >Importance: Low
> > > > >> >
> > > > >> >i'm helping a bud here at work set up a termial
> > > > server to remote into >>his
> > > > >> >other routers. he has a 2511 with 16 async
> > > > ports, the serial to rj45 >>type
> > > > >> >(2 serial connections on the 2511) so he has the
> > > > octal cables. i'm >> >assuming
> > > > >> >
> > > > >> >that the octal cables go into the console ports.
> > > other than that, >what
> > > > >>is
> > > > >> >needed on the 2511 to telnet into the other
> > > routers. i know you >need:
> > > > >> >
> > > > >> >ip host r1 2001 1.1.1.1 <----------- is the
> > > > address arbitrary? >> >
> > > > >> >do you confgure the following on the line
> > > > console or line? >> >line con 0
> > > > >> >or
> > > > >> >line 1 16?
> > > > >> >
> > > > >> >tarnsport output(input?) all
> > > > >> >modem inout
> > > > >> >
> > > > >> >where does this go?
> > > > >> >
> > > > >> >TIA
> > > > >> >
> > > > >>
> > >
> > > >
> >_________________________________________________________
> ________ >> >Dont just search. Find. Check out the >new
> > > > MSN Search! >>
> > >
> > > >
> >http://search.msn.click-url.com/go/onm00200636ave/direct/
> > > > 01/ >> > >>
> > > >
> > >
> > > >
> >_________________________________________________________
> > > > ______________ >> >Subscription information may be
> > > > found at: >>
> > > >http://www.groupstudy.com/list/CCIELab.html >> >
> > >
> > > >
> >>________________________________________________________
> > > _________ >>Express yourself instantly with MSN
> > > Messenger! Download today - it's >FREE! >
> > >
> > > >
> >>http://messenger.msn.click-url.com/go/onm00200471ave/dir
> > > ect/01/ >> >
> > >
> > > >
> >>________________________________________________________
> > > > _______________ >>Subscription information may be
> > > > found at:
> > > >>http://www.groupstudy.com/list/CCIELab.html > >
> > >
> > > >
> >_________________________________________________________
> > > ________ >Express yourself instantly with MSN
> > > Messenger! Download today - it's >FREE! >
> > >
> > > >
> >http://messenger.msn.click-url.com/go/onm00200471ave/dire
> > > ct/01/ > >
> > >
> > > >
> >_________________________________________________________
> > > > ______________ >Subscription information may be
> > > found at: >http://www.groupstudy.com/list/CCIELab.html
> > > >
> > >
> >_________________________________________________________
> > > ________ >Express yourself instantly with MSN
> > > Messenger! Download today - it's FREE!
> > >
> >http://messenger.msn.click-url.com/go/onm00200471ave/dire
> > ct/01/ >
> > >
> > >
> __________________________________________________________
> > > _______ Express yourself instantly with MSN Messenger!
> > Download today - it's FREE! >
> >http://messenger.msn.click-url.com/go/onm00200471ave/dire
> > ct/01/ >
> > >
> > >
> __________________________________________________________
> > > _____________ Subscription information may be found
> at: http://www.groupstudy.com/list/CCIELab.html >
> >Ian Stong
> >http://www.ccie4u.com
> >"Rack Rentals and Lab Scenarios starting at only $12"
> >support@ccie4u.com
> >
> >_________________________________________________________
> ______________ >Subscription information may be found at:
> >http://www.groupstudy.com/list/CCIELab.html
>
> __________________________________________________________
> _______ Dont just search. Find. Check out the new MSN
> Search!
>
http://search.msn.click-url.com/go/onm00200636ave/direct/01/
>
> __________________________________________________________
> _____________ Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
Ian Stong
http://www.ccie4u.com
"Rack Rentals and Lab Scenarios starting at only $12"
support@ccie4u.com
This archive was generated by hypermail 2.1.4 : Sun Sep 04 2005 - 17:00:30 GMT-3