From: 22Cent@gmail.com
Date: Wed May 25 2005 - 19:06:48 GMT-3
I'm sorry for beating a dead horse. So.. currently I have a 2621( not
XM )with 12.2(15)T14 loaded and 64/16. Why am i not able to run OSPF
over ipv6 ? ISIS and RIP look to be fine. TIA
Ray
On 5/25/05, Brian McGahan <bmcgahan@internetworkexpert.com> wrote:
> Rik,
>
> The problem is that the 2610 and 2611 can't recognize 32Mb flash
> simms. All the 2600 and 2600XM images are effectively the same, the
> only difference is that the 2620 and 2621 can recognize 32Mb flash simms
> (2610 and 2611 cannot), and the 2600XMs can all support more RAM and
> flash. So while you are correct that the Software Advisor says that the
> 2610 Enterprise Plus image supports this feature, the flash is not large
> enough to hold the image.
>
> Here is the image you would want:
>
> BB2#dir slot0:
> Directory of slot0:/
>
> 1 -rw- 18312232 <no date>
> c2600-js-mz.122-15.T14.bin
>
> 20709376 bytes total (2397080 bytes free)
>
> Here is a 2610 with a 16Mb flash:
>
> Rack1R1#dir flash:
> Directory of flash:/
>
> 1 -rw- 15184112 <no date>
> c2600-j1s3-mz.122-15.T14.bin
>
> 16252928 bytes total (1068752 bytes free)
> Rack1R1#
>
> The image size is 18,312,232 but the flash size is 16,252,928.
>
>
> HTH,
>
> Brian McGahan, CCIE #8593
> bmcgahan@internetworkexpert.com
>
> Internetwork Expert, Inc.
> http://www.InternetworkExpert.com
> Toll Free: 877-224-8987 x 705
> Outside US: 775-826-4344 x 705
> 24/7 Support: http://forum.internetworkexpert.com
> Live Chat: http://www.internetworkexpert.com/chat/
>
>
> > -----Original Message-----
> > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf
> Of
> > Guyler, Rik
> > Sent: Tuesday, May 24, 2005 6:56 PM
> > To: 'ccielab@groupstudy.com'
> > Subject: RE: Command "ipv6 ospf" on 2600 with IOS 12.2(15)T15
> >
> > So I take it since he has to boot the XM image from rommon that
> copying it
> > to flash won't work or did I miss something else in this thread? Is
> this
> > because he is trying to boot an XM image on a non-XM router?
> >
> > Rik
> >
> > -----Original Message-----
> > From: Brian McGahan [mailto:bmcgahan@internetworkexpert.com]
> > Sent: Tuesday, May 24, 2005 7:08 PM
> > To: Bob Nelson; Cisco certification
> > Subject: RE: Command "ipv6 ospf" on 2600 with IOS 12.2(15)T15
> >
> > Bob,
> >
> > Once you set the environment variables in rommon they will stay.
> > For further booting you need to type just the "tftpdnld -r" command
> and
> > it will use the previously configured image name and tftp server.
> You
> > could script this in securecrt through VBScript.
> >
> > HTH,
> >
> > Brian McGahan, CCIE #8593
> > bmcgahan@internetworkexpert.com
> >
> > Internetwork Expert, Inc.
> > http://www.InternetworkExpert.com
> > Toll Free: 877-224-8987 x 705
> > Outside US: 775-826-4344 x 705
> > 24/7 Support: http://forum.internetworkexpert.com
> > Live Chat: http://www.internetworkexpert.com/chat/
> >
> >
> > > -----Original Message-----
> > > From: Bob Nelson [mailto:nelsnjr@cox.net]
> > > Sent: Tuesday, May 24, 2005 4:24 PM
> > > To: Brian McGahan; Chad Hintz; Mathew; Cisco certification
> > > Subject: Re: Command "ipv6 ospf" on 2600 with IOS 12.2(15)T15
> > >
> > > Yep, that works!
> > >
> > > Router(config)#int s0/0
> > > Router(config-if)#ipv6 ?
> > > IPv6 interface subcommands:
> > > address Configure IPv6 address on interface
> > > cef Cisco Express Forwarding for IPv6
> > > enable Enable IPv6 on interface
> > > mtu Set IPv6 Maximum Transmission Unit
> > > nat Enable IPv6 NAT on interface
> > > nd IPv6 interface Neighbor Discovery subcommands
> > > ospf OSPF interface commands
> > > redirects Enable sending of ICMP Redirect messages
> > > rip Configure RIP routing protocol
> > > router IPv6 Router interface commands
> > > traffic-filter Access control list for packets
> > > unnumbered Preferred interface for source address selection
> > > verify Enable per packet validation
> > >
> > > What I don't know is how to get the router to boot that way every
> > time.
> > > I can get it to the ROM mode, but is there a way to automatically
> make
> > it
> > > do
> > > the tftpdnld -r?
> > >
> > > Bob
> > > ----- Original Message -----
> > > From: "Brian McGahan" <bmcgahan@internetworkexpert.com>
> > > To: "Chad Hintz" <ccie_2b2004@yahoo.com>; "Mathew"
> > <mathew@oztralia.com>;
> > > "Cisco certification" <ccielab@groupstudy.com>
> > > Sent: Tuesday, May 24, 2005 7:28 AM
> > > Subject: RE: Command "ipv6 ospf" on 2600 with IOS 12.2(15)T15
> > >
> > >
> > > > You can boot the 2600XM enterprise plus image from TFTP to the
> 2610
> > or
> > > > 2611 via the "tftpdnld -r" command in rommon.
> > > >
> > > > HTH,
> > > >
> > > > Brian McGahan, CCIE #8593
> > > > bmcgahan@internetworkexpert.com
> > > >
> > > > Internetwork Expert, Inc.
> > > > http://www.InternetworkExpert.com
> > > > Toll Free: 877-224-8987 x 705
> > > > Outside US: 775-826-4344 x 705
> > > > 24/7 Support: http://forum.internetworkexpert.com
> > > > Live Chat: http://www.internetworkexpert.com/chat/
> > > >
> > > >
> > > > > -----Original Message-----
> > > > > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On
> > Behalf
> > > > Of
> > > > > Chad Hintz
> > > > > Sent: Tuesday, May 24, 2005 7:11 AM
> > > > > To: Mathew; 'Cisco certification'
> > > > > Subject: Re: Command "ipv6 ospf" on 2600 with IOS 12.2(15)T15
> > > > >
> > > > > The 2610 does not support this feature, you need a 2620 or 21 to
> > use
> > > > > ospfv3.
> > > > >
> > > > > HTH,
> > > > >
> > > > > Chad
> > > > >
> > > > >
> > > > > Hi Team
> > > > >
> > > > > Does anybody know why I can not enable IPV6 OSPF on 2600 with
> IOS
> > ver
> > > > > 12.2(15)T15?
> > > > >
> > > > > Even after configuring "ipv6 unicast-routing" and "ipv6 enable"
> > under
> > > > the
> > > > > interface, I do not see
> > > > >
> > > > > a OSPF option.
> > > > >
> > > > > Does anybody know why it is so?
> > > > >
> > > > > R2(config-if)#ipv6 ?
> > > > > IPv6 interface subcommands:
> > > > > address Configure IPv6 address on interface cef Cisco Express
> > > > > Forwarding for IPv6 enable Enable IPv6 on interface mtu Set IPv6
> > > > > Maximum Transmission Unit nat Enable IPv6 NAT on interface nd
> IPv6
> > > > > interface Neighbor Discovery subcommands redirects Enable
> sending
> > > > > of ICMP Redirect messages rip Configure RIP routing protocol
> > > > > router IPv6 Router interface commands traffic-filter Access
> > > > > control list for packets unnumbered Preferred interface for
> source
> > > > > address selection verify Enable per packet validation
> > > > >
> > > > > R2(config-if)#ipv6 ro
> > > > > R2(config-if)#ipv6 router ?
> > > > > isis IS-IS Routing for IPv6
> > > > >
> > > > > R2(config-if)#ipv6 router
> > > > > R2(config-if)#do sho ver
> > > > > Cisco Internetwork Operating System Software IOS (tm) C2600
> > > > > Software (C2600-J1S3-M), Version 12.2(15)T15,
> > RELEASE
> > > > > SOFTWARE (fc1)
> > > > > Technical Support: http://www.cisco.com/techsupport Copyright
> (c)
> > > > > 1986-2005 by cisco Systems, Inc.
> > > > > Compiled Thu 03-Mar-05 03:28 by hqluong Image text-base:
> > > > > 0x80008098, data-base: 0x81960D40
> > > > >
> > > > > ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE
> (fc1)
> > > > > ROM: C2600 Software (C2600-J1S3-M), Version 12.2(15)T15, RELEASE
> > > > SOFTWARE
> > > > > (fc1)
> > > > >
> > > > > R2 uptime is 47 minutes
> > > > > System returned to ROM by power-on System image file is
> > > > > "flash:c2600-j1s3-mz.122-15.T15.bin"
> > > > >
> > > > > cisco 2610 (MPC860) processor (revision 0x203) with 61440K/4096K
> > bytes
> > > > of
> > > > > memory.
> > > > > Processor board ID JAD05090GQQ (1222274526) M860 processor: part
> > > > > number 0, mask 49 Bridging software.
> > > > > X.25 software, Version 3.0.0.
> > > > > TN3270 Emulation software.
> > > > > 1 Ethernet/IEEE 802.3 interface(s)
> > > > > 2 Serial(sync/async) network interface(s)
> > > > > 16 terminal line(s)
> > > > > 32K bytes of non-volatile configuration memory.
> > > > > 16384K bytes of processor board System flash (Read/Write)
> > > > >
> > > > > Configuration register is 0x2102
> > > > >
> > > > > R2(config-if)#
> > > > >
> > > > >
> > > >
> >
> _______________________________________________________________________
> > > > > Subscription information may be found at:
> > > > > http://www.groupstudy.com/list/CCIELab.html
> > > > >
> > > > > __________________________________________________
> > > > > Do You Yahoo!?
> > > > > Tired of spam? Yahoo! Mail has the best spam protection around
> > > > > http://mail.yahoo.com
> > > > >
> > > > >
> > > >
> >
> _______________________________________________________________________
> > > > > Subscription information may be found at:
> > > > > http://www.groupstudy.com/list/CCIELab.html
> > > >
> > > >
> >
> _______________________________________________________________________
> > > > Subscription information may be found at:
> > > > http://www.groupstudy.com/list/CCIELab.html
> >
> >
> _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
> >
> >
> _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Fri Jun 03 2005 - 10:12:02 GMT-3