From: Chad Hintz (ccie_2b2004@yahoo.com)
Date: Tue May 24 2005 - 11:58:27 GMT-3
Learn something new everyday, so much for the feature navigator :-)
Brian McGahan <bmcgahan@internetworkexpert.com> wrote:You can boot the 2600XM enterprise plus image from TFTP to the 2610 or
2611 via the "tftpdnld -r" command in rommon.
HTH,
Brian McGahan, CCIE #8593
bmcgahan@internetworkexpert.com
Internetwork Expert, Inc.
http://www.InternetworkExpert.com
Toll Free: 877-224-8987 x 705
Outside US: 775-826-4344 x 705
24/7 Support: http://forum.internetworkexpert.com
Live Chat: http://www.internetworkexpert.com/chat/
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf
Of
> Chad Hintz
> Sent: Tuesday, May 24, 2005 7:11 AM
> To: Mathew; 'Cisco certification'
> Subject: Re: Command "ipv6 ospf" on 2600 with IOS 12.2(15)T15
>
> The 2610 does not support this feature, you need a 2620 or 21 to use
> ospfv3.
>
> HTH,
>
> Chad
>
>
> Hi Team
>
> Does anybody know why I can not enable IPV6 OSPF on 2600 with IOS ver
> 12.2(15)T15?
>
> Even after configuring "ipv6 unicast-routing" and "ipv6 enable" under
the
> interface, I do not see
>
> a OSPF option.
>
> Does anybody know why it is so?
>
> R2(config-if)#ipv6 ?
> IPv6 interface subcommands:
> address Configure IPv6 address on interface
> cef Cisco Express Forwarding for IPv6
> enable Enable IPv6 on interface
> mtu Set IPv6 Maximum Transmission Unit
> nat Enable IPv6 NAT on interface
> nd IPv6 interface Neighbor Discovery subcommands
> redirects Enable sending of ICMP Redirect messages
> rip Configure RIP routing protocol
> router IPv6 Router interface commands
> traffic-filter Access control list for packets
> unnumbered Preferred interface for source address selection
> verify Enable per packet validation
>
> R2(config-if)#ipv6 ro
> R2(config-if)#ipv6 router ?
> isis IS-IS Routing for IPv6
>
> R2(config-if)#ipv6 router
> R2(config-if)#do sho ver
> Cisco Internetwork Operating System Software
> IOS (tm) C2600 Software (C2600-J1S3-M), Version 12.2(15)T15, RELEASE
> SOFTWARE (fc1)
> Technical Support: http://www.cisco.com/techsupport
> Copyright (c) 1986-2005 by cisco Systems, Inc.
> Compiled Thu 03-Mar-05 03:28 by hqluong
> Image text-base: 0x80008098, data-base: 0x81960D40
>
> ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
> ROM: C2600 Software (C2600-J1S3-M), Version 12.2(15)T15, RELEASE
SOFTWARE
> (fc1)
>
> R2 uptime is 47 minutes
> System returned to ROM by power-on
> System image file is "flash:c2600-j1s3-mz.122-15.T15.bin"
>
> cisco 2610 (MPC860) processor (revision 0x203) with 61440K/4096K bytes
of
> memory.
> Processor board ID JAD05090GQQ (1222274526)
> M860 processor: part number 0, mask 49
> Bridging software.
> X.25 software, Version 3.0.0.
> TN3270 Emulation software.
> 1 Ethernet/IEEE 802.3 interface(s)
> 2 Serial(sync/async) network interface(s)
> 16 terminal line(s)
> 32K bytes of non-volatile configuration memory.
> 16384K bytes of processor board System flash (Read/Write)
>
> Configuration register is 0x2102
>
> R2(config-if)#
>
>
This archive was generated by hypermail 2.1.4 : Fri Jun 03 2005 - 10:12:01 GMT-3