From: Brian McGahan (bmcgahan@internetworkexpert.com)
Date: Wed Mar 16 2005 - 19:53:27 GMT-3
Are they in different areas though? What are the NET addresses of R2,
R3, and R6?
Brian McGahan, CCIE #8593
bmcgahan@internetworkexpert.com
Internetwork Expert, Inc.
http://www.InternetworkExpert.com
Toll Free: 877-224-8987 x 705
Outside US: 775-826-4344 x 705
24/7 Support: http://forum.internetworkexpert.com
Live Chat: http://www.internetworkexpert.com/chat/
> -----Original Message-----
> From: kuldip singh [mailto:dipa.singh@gmail.com]
> Sent: Wednesday, March 16, 2005 4:49 PM
> To: Brian McGahan
> Cc: Group Study
> Subject: Re: IE LAB2 ISIS
>
> Hi Brian,
>
> R2 has L2 adjacency with R3 as show below:
>
> Rack1R2#sh clns neigh
>
> System Id Interface SNPA State Holdtime Type
> Protocol
> Rack1R6 Et0/0 0060.2fa3.da00 Up 8 L1
IS-IS
> Rack1R3 Se0/1 *HDLC* Up 28 L2
IS-IS
>
>
>
>
> On Wed, 16 Mar 2005 17:22:33 -0500, Brian McGahan
> <bmcgahan@internetworkexpert.com> wrote:
> > Kuldip,
> >
> > Does R2 have any L2 adjacencies with routers in other areas?
> >
> > Brian McGahan, CCIE #8593
> > bmcgahan@internetworkexpert.com
> >
> > Internetwork Expert, Inc.
> > http://www.InternetworkExpert.com
> > Toll Free: 877-224-8987 x 705
> > Outside US: 775-826-4344 x 705
> > 24/7 Support: http://forum.internetworkexpert.com
> > Live Chat: http://www.internetworkexpert.com/chat/
> >
> > > -----Original Message-----
> > > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On
Behalf
> > Of
> > > kuldip singh
> > > Sent: Wednesday, March 16, 2005 1:15 PM
> > > To: Group Study
> > > Subject: IE LAB2 ISIS
> > >
> > > Hi
> > >
> > > I have just been doing lab2 in IE and for some reason I just
can't
> > get
> > > the
> > > default route being sent to R6.
> > >
> > > R2: is level-1-2 router and Router 6 is level-1 router but using
sub-
> > > interface
> > > on ethernet. If I change R6 to level-1-2 router than I can see all
the
> > > routes ok on R6. But R6 is configured as Level-1 I can't see the
> > default.
> > >
> > > Any suggestions:
> > >
> > > config on R2:
> > >
> > > interface Ethernet0/0
> > > ip address 132.1.26.2 255.255.255.0
> > > ip router isis
> > > half-duplex
> > > isis circuit-type level-1
> > >
> > > router isis
> > > net 49.0001.0001.0001.0002.00
> > > summary-address 51.0.0.0 255.248.0.0
> > > redistribute ospf 1
> > > passive-interface Loopback0
> > >
> > >
> > > R2: has L1 and L2 routes:
> > >
> > >
> > > R6:
> > > interface Ethernet0.26
> > > encapsulation dot1Q 26
> > > ip address 132.1.26.6 255.255.255.0
> > > ip router isis
> > >
> > >
> > > router isis
> > > net 49.0001.0001.0001.0006.00
> > > passive-interface Loopback0
> > > is-type level-1
> > >
> > >
> > > Routes on R6:
> > >
> > > Rack1R6#sh ip route isis
> > > 51.0.0.0/16 is subnetted, 8 subnets
> > > i L1 51.3.0.0 [115/10] via 54.1.2.254, ATM0.1
> > > i L1 51.2.0.0 [115/10] via 54.1.2.254, ATM0.1
> > > i L1 51.1.0.0 [115/10] via 54.1.2.254, ATM0.1
> > > i L1 51.0.0.0 [115/10] via 54.1.2.254, ATM0.1
> > > i L1 51.7.0.0 [115/10] via 54.1.2.254, ATM0.1
> > > i L1 51.6.0.0 [115/10] via 54.1.2.254, ATM0.1
> > > i L1 51.5.0.0 [115/10] via 54.1.2.254, ATM0.1
> > > i L1 51.4.0.0 [115/10] via 54.1.2.254, ATM0.1
> > > 54.0.0.0/24 is subnetted, 2 subnets
> > > i L1 54.1.4.0 [115/20] via 54.1.2.254, ATM0.1
> > > 150.1.0.0/24 is subnetted, 2 subnets
> > > i L1 150.1.2.0 [115/10] via 132.1.26.2, Ethernet0.26
> > > Rack1R6#
> > >
> > > Rack1R6#sh clns neig
> > >
> > > System Id Interface SNPA State Holdtime
Type
> > > Protocol
> > > Rack1R2 Et0.26 0030.9436.24e0 Up 26 L1
> > IS-IS
> > > BB1 AT0.1 VC 6 Up 27 L1
> > IS-IS
> > > Rack1R6#
> > >
> > > Appreciate any info Thanks
> > >
> > >
> >
This archive was generated by hypermail 2.1.4 : Sun Apr 03 2005 - 17:56:46 GMT-3