From: marvin greenlee (marvin@ccbootcamp.com)
Date: Thu Mar 03 2005 - 16:30:21 GMT-3
Other than being able to see the default values before you start configuring
parameters, I don't see any real benefit.
Marvin Greenlee, CCIE#12237, CCSI# 30483
Network Learning Inc
marvin@ccbootcamp.com
www.ccbootcamp.com (Cisco Training)
-----Original Message-----
From: Gajewski Mariusz [mailto:Mariusz.Gajewski@telekomunikacja.pl]
Sent: Thursday, March 03, 2005 10:15 AM
To: marvin greenlee; ccielab@groupstudy.com
Subject: RE: GLBP [bcc][faked-from] [mx]
Hi Marvin,
thanks for getting back to me.
if so , what exactly such command do ? Enable the group ? If I
should preconfigure options first as doc says, I can see no diffrence in sh
glbp , between e.g.
Glbp 1 ip <enter>
glbp 1 priority 110
glbp 1 preempt
And
glbp 1 priority 110
glbp 1 preempt
I've read info on doc-cd and that's not as clear to me as it shuld be :( .
-----Original Message-----
From: marvin greenlee [mailto:marvin@ccbootcamp.com]
Sent: Thursday, March 03, 2005 7:03 PM
To: Gajewski Mariusz; ccielab@groupstudy.com
Subject: RE: GLBP [bcc][faked-from]
Per the configuration document, it is recommended to configure the optional
features (timers, priority, etc.) before enabling the group.
"...Be aware that as soon as you enable a GLBP group, that group is
operating. It is possible that if you first enable a GLBP group before
customizing GLBP, the router could take over control of the group and become
the AVG before you have finished customizing the feature. Therefore, if you
plan to customize GLBP, it is a good idea to do so before enabling GLBP...."
Cisco - GLBP - Gateway Load Balancing Protocol
http://www.cisco.com/en/US/products/sw/iosswrel/ps1839/products_feature_guid
e09186a00801541c8.html
Marvin Greenlee, CCIE#12237, CCSI# 30483
Network Learning Inc
marvin@ccbootcamp.com
www.ccbootcamp.com (Cisco Training)
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
Gajewski Mariusz
Sent: Thursday, March 03, 2005 9:51 AM
To: ccielab@groupstudy.com
Subject: GLBP [bcc][faked-from]
Importance: Low
hi guys,
we can "configure" GLBP on int just by hitting enter after "ip"
router(config-if)#glbp 1 ip <enter>
but if we do so glbp is in fact disabled, there are no AVF and no AVG :
FastEthernet0/0 - Group 1
State is Disabled
Virtual IP address is unknown
Hello time 3 sec, hold time 10 sec
Redirect time 600 sec, forwarder time-out 14400 sec
Preemption enabled, min delay 0 sec
Active is unknown
Standby is unknown
Priority 100 (default)
Weighting 100 (default 100), thresholds: lower 1, upper 100
Load balancing: round-robin
There are no forwarders
can someone explain to me what is this "functionality" for , because i can't
understand for what purpose we might skip virtual address ?
thanks,
Mariusz
This archive was generated by hypermail 2.1.4 : Sun Apr 03 2005 - 17:56:40 GMT-3