From: Michael Doherty (z0rand3r@hotmail.com)
Date: Sat Feb 26 2005 - 12:52:29 GMT-3
Yes, spaces are required before either the hyphen or comma in the range
command. Commas are also useful when you want to include multiple interface
types in the range command. For example, you can use the following range
command to make the same configuration command changes to interfaces
fa0/1-12, 15 and g0/1-2 (i.e., changing the switchport mode from desirable
to trunk):
interface range fastethernet 0/1 - 12 , fastethernet 0/15 , gigabitethernet
0/1 - 2
Hope that helps.
Mike
>From: "ccie2be" <ccie2be@nyc.rr.com>
>Reply-To: "ccie2be" <ccie2be@nyc.rr.com>
>To: "'Dillon Yang'" <gzdillon@hotmail.com>, "'Group Study'"
><ccielab@groupstudy.com>
>Subject: RE: Specifying many FA interfaces in one line in a Cat3550
>Date: Sat, 26 Feb 2005 10:22:28 -0500
>
>I'm pretty sure, not 100%, however, discontinuous interfaces can also be
>listed with the interface range by uses a comma.
>
>Using a macro is good if you have to refer back to that same list of
>interfaces multiple times. But, if you don't expect to need that
>reference,
>it's probably easier and faster to just list the interfaces in the
>interface
>range command.
>
>Off-hand, I can't recall if spaces are needed before or after the comma.
>
>HTH, Tim
>
>-----Original Message-----
>From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
>Dillon Yang
>Sent: Saturday, February 26, 2005 10:12 AM
>To: Group Study
>Subject: Re: Specifying many FA interfaces in one line in a Cat3550
>
>Alternate method is command macro for discontiguous interface number
>
>HTH
>
>dillon
>
>
>----- Original Message -----
>From: "ccie2be" <ccie2be@nyc.rr.com>
>To: "'Chris Aguillo'" <ccaguillo1@hotpop.com>; "'ccielab'"
><ccielab@groupstudy.com>
>Sent: Saturday, February 26, 2005 9:03 PM
>Subject: RE: Specifying many FA interfaces in one line in a Cat3550
>
>
> > Use the interface range command.
> >
> > For example,
> >
> > Interface range fa0/10 - 13
> >
> > Note that you must have a space before and after the hyphen.
> >
> > HTH, Tim
> >
> > -----Original Message-----
> > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> > Chris Aguillo
> > Sent: Saturday, February 26, 2005 7:18 AM
> > To: ccielab
> > Subject: Specifying many FA interfaces in one line in a Cat3550
> >
> > Hi Guys,
> >
> > I would like to ask on how to configure many interfaces of cat3550 in
> > one go but specifying many interfaces to be configured.
> >
> > Thanks...
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
>
>_______________________________________________________________________
>Subscription information may be found at:
>http://www.groupstudy.com/list/CCIELab.html
>
>_______________________________________________________________________
>Subscription information may be found at:
>http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Thu Mar 03 2005 - 08:51:25 GMT-3