From: Valdas Slimas (valdas.slimas@gmail.com)
Date: Mon Jan 24 2005 - 17:36:10 GMT-3
Hi,
I just have verified, does its possible on one physical port to have
EoMPLS tunnel on one subinterface and l3 routing on another
subinterface (separate vlan's).
EoMPLS and IP address on the same subinterface is not supported, of course.
regards,
On Mon, 24 Jan 2005 23:59:25 +0530, Swaroop Potdar
<swarooppotdar@hotmail.com> wrote:
> HI Valdas,
>
> Verified ? you mean on these platforms the same subinterface supports EoMPLS
> and assigning an IP address too ??
>
> something like this
>
> interface GigabitEthernet0/0.1
> "ip address x.x.x.x " ??
> encapsulation dot1q 30
> "mpls l2transport route 1.0.0.2 300" ??
>
> on your 6500 or 7600 you can assign an ip address to the vlan interface and
> also do a L2transport.
>
> But on subinterface ...?? .if you did it...can u tell which IOS you used???
>
>
> >From: Valdas Slimas <valdas.slimas@gmail.com>
> >Reply-To: Valdas Slimas <valdas.slimas@gmail.com>
> >To: ccielab@groupstudy.com, phase90@comcast.net
> >Subject: Re: EOMPLS ????
> >Date: Mon, 24 Jan 2005 10:38:32 +0200
> >
> >Jerry,
> >
> >Yes, I have veryfied, its working fine for me on 3750ME, 6500, 10720
> >and GSR 4xGE card. GSR 3xGE card have problem, because port can work
> >only in l2 or l3 mode.
> >Have no equipment to check with Engine4+ GSR card.
> >
> >regards,
> >
> >
> >On Sat, 22 Jan 2005 13:14:50 -0500, phase90 <phase90@comcast.net> wrote:
> > > Valdas,
> > >
> > > I know layer-2 & layer-3 can be done on the same blade
> > > because I've had this
> > > configuration with gigabit blade in a Catalyst 8540. Your issue may
> >have to
> > > do with MPLS or you have a different blade that doesn't support it.
> > >
> > > Jerry
> > > ----- Original Message -----
> > > From: "Valdas Slimas" <valdas.slimas@gmail.com>
> > > To: "Casey Paul (IE)" <Paul.Casey@o2.com>
> > > Cc: <ccielab@groupstudy.com>
> > > Sent: Friday, January 21, 2005 8:43 AM
> > > Subject: Re: EOMPLS ????
> > >
> > > > Hi,
> > > >
> > > > >bla-pe-01(config)#interface GigabitEthernet2/3/0.10
> > > > >bla-pe-01(config-subif)#xconnect 10.160.160.9 10 encapsulation mpls
> > > > >Incompatible with ip address command on Gi2/3/0.10 - command
> >rejected.
> > > > Could U please check, does ip address on subinterface is correct.
> > > >
> > > > > Is the point below in an issue ??? Is it saying we cant do layer3
> >and
> > > > > layer2 at the same time on the same card.
> > > > This restriction exist on 3GE (engine2) card, and removed on 4GE
> > > > (Engine3 or ISE) card. No idea about EPA-GE/FE-BBRD (Engine4+)
> > > >
> > > > /Valdas
> > > >
> > > >
> >_______________________________________________________________________
> > > > Subscription information may be found at:
> > > > http://www.groupstudy.com/list/CCIELab.html
> > >
> > >
> >
> >
> >--
> >/Valdas
> >
> >_______________________________________________________________________
> >Subscription information may be found at:
> >http://www.groupstudy.com/list/CCIELab.html
>
> Regards,
> Swaroop.
> ------------------------------------------------------------------
> Life Is Short & Sweet.
> Live It To The Fullest.
> ------------------------------------------------------------------
>
> _________________________________________________________________
> Trailblazer Narain Karthikeyan. Know more about him 'n his life.
> http://server1.msn.co.in/sp04/tataracing/ Stay in the loop with Tata Racing!
>
>
-- /Valdas
This archive was generated by hypermail 2.1.4 : Wed Feb 02 2005 - 22:10:25 GMT-3