From: Anthony Sequeira (terry.francona@gmail.com)
Date: Fri Dec 31 2004 - 04:29:29 GMT-3
Any thoughts on what causes the error below would be very much appreciated!
R4#debug isdn events
ISDN events debugging is on
R4#ping 160.10.20.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 160.10.20.2, timeout is 2 seconds:
1d08h: ISDN BR0: Outgoing call id = 0x800B, dsl 0
1d08h: ISDN BR0: Event: Call to 8358661 at 64 Kb/s
1d08h: ISDN BR0: process_bri_call(): call id 0x800B, called_number
8358661, speed 64, call
type DATA
1d08h: CC_CHAN_GetIdleChanbri: dsl 0
1d08h: Found idle channel B1
1d08h: ISDN BR0: received HOST_PROCEEDING call_id 0x800B
1d08h: ISDN BR0: received HOST_PROGRESS call_id 0x800B
1d08h: ISDN BR0: received HOST_PROGRESS call_id 0x800B
1d08h: ISDN BR0: HOST_PROGRESS: DEV_CALL_PROGRESSING VOICE ERROR:
Bearer capability not ava
ilable(0x3A): bchan 0, call id 0x800B.....
Success rate is 0 percent (0/5)
R2 CONFIG
interface BRI0
ip address 160.10.20.2 255.255.255.0
no ip directed-broadcast
encapsulation ppp
dialer map ip 160.10.20.4 name R4 broadcast 8358662
dialer-group 1
isdn switch-type basic-ni
isdn spid1 0835866101 8358661
isdn spid2 0835866301 8358663
dialer-list 1 protocol ip permit
R2#show isdn st
Global ISDN Switchtype = basic-ni
ISDN BRI0 interface
dsl 0, interface ISDN Switchtype = basic-ni
Layer 1 Status:
ACTIVE
Layer 2 Status:
TEI = 100, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
TEI = 101, Ces = 2, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
Spid Status:
TEI 100, ces = 1, state = 5(init)
spid1 configured, spid1 sent, spid1 valid
Endpoint ID Info: epsf = 0, usid = 1, tid = 1
TEI 101, ces = 2, state = 5(init)
spid2 configured, spid2 sent, spid2 valid
Endpoint ID Info: epsf = 0, usid = 3, tid = 1
Layer 3 Status:
0 Active Layer 3 Call(s)
Activated dsl 0 CCBs = 0
The Free Channel Mask: 0x80000003
Total Allocated ISDN CCBs = 0
R4 CONFIG
interface BRI0
ip address 160.10.20.4 255.255.255.0
encapsulation ppp
dialer map ip 160.10.20.2 name R2 broadcast 8358661
dialer-group 1
isdn switch-type basic-ni
isdn spid1 0835866201 8358662
isdn spid2 0835866401 8358664
dialer-list 1 protocol ip permit
R4#show isdn st
Global ISDN Switchtype = basic-ni
ISDN BRI0 interface
dsl 0, interface ISDN Switchtype = basic-ni
Layer 1 Status:
ACTIVE
Layer 2 Status:
TEI = 98, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
TEI = 99, Ces = 2, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
TEI 98, ces = 1, state = 5(init)
spid1 configured, spid1 sent, spid1 valid
Endpoint ID Info: epsf = 0, usid = 2, tid = 1
TEI 99, ces = 2, state = 5(init)
spid2 configured, spid2 sent, spid2 valid
Endpoint ID Info: epsf = 0, usid = 4, tid = 1
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 0 CCBs = 0
The Free Channel Mask: 0x80000003
Number of L2 Discards = 0, L2 Session ID = 27
Total Allocated ISDN CCBs = 0
This archive was generated by hypermail 2.1.4 : Mon Jan 03 2005 - 10:31:33 GMT-3