From: Erick Bergquist (ebergquist@ameritech.net)
Date: Thu Dec 16 2004 - 03:03:34 GMT-3
Also, the VWIC-2MFT has one clock chip on it so can
receive clock on one port (line) and provide clock on
other port (internal). Thats my only gripe with this
card from my experiences with it is that the timing on
the T1s coming in has to be planned out right. I have
seen 2 T1s configured as line clocking coming from
same clock source work fine though.
If you have VWIC-2MFT with 2 line clocked T1s in it,
then usually on the non-primary port you may see slip
seconds. This can really cause problems if your doing
voice over it.
Anyone else run into this?
--- alsontra@hotmail.com wrote:
> Geert Nijs,
>
> A product note for the VWIC-2MFT-G703 states that
> the card supports support
> all the features of the other VWIC models.
>
>
> "Specific models to support E1 G.703 unframed for
> utilizing the full 2.048
> Mbps (Note: The G.703 models can also be configured
> for framed mode where
> they support all the features of the other VWIC
> models)"
>
>
http://www.cisco.com/en/US/partner/products/hw/routers/ps259/products_data_s
> heet09186a0080091b9c.html
>
> I've got run of the mill VWIC-2MFT-T1 doing IMA at
> the moment and I'm not
> pleased. Many of the errors or conditions result in
> failures that require
> reboots. Anyone else having issue with the ATM AIM
> VWIC solution?
>
> (They never should have EOL the old IMA modules)
>
> Al
>
> -----Original Message-----
> From: nobody@groupstudy.com
> [mailto:nobody@groupstudy.com] On Behalf Of
> Geert Nijs
> Sent: Wednesday, December 15, 2004 7:04 AM
> To: ccielab@groupstudy.com
> Subject: VWIC-2MFT-G703 with ATM AIM module ?
>
> Hello group,
>
> Does anyone know if the ATM AIM module for 2600
> routers is supported with
> VWIC-2MFT-G703 modules ??
>
> There are bundles for sale with E1/T1 VWIC modules,
> but none with G703
> modules ?
>
> Will the ATM AIM modle work with the G703 modules ??
> Any ideas ??
>
>
> Regards,
> Geert Nijs
> CCIE #13729
>
############################################################################
> #########
> This e-mail and any attached files are confidential
> and may be legally
> privileged.
> If you are not the addressee, any disclosure,
> reproduction, copying,
> distribution,
> or other dissemination or use of this communication
> is strictly prohibited.
> If you have received this transmission in error
> please notify Simac
> immediately
> and then delete this e-mail.
>
> Simac has taken all reasonable precautions to avoid
> virusses in this email.
> Simac does not accept liability for damage by
> virusses, for the correct and
> complete
> transmission of the information, nor for any delay
> or interruption of the
> transmission,
> nor for damages arising from the use of or reliance
> on the information.
>
> All e-mail messages addressed to, received or sent
> by Simac or Simac
> employees
> are deemed to be professional in nature.
> Accordingly, the sender or
> recipient of
> these messages agrees that they may be read by other
> Simac employees than
> the official
> recipient or sender in order to ensure the
> continuity of work-related
> activities
> and allow supervision thereof.
>
############################################################################
> #########
>
>
This archive was generated by hypermail 2.1.4 : Mon Jan 03 2005 - 10:31:27 GMT-3