From: ccie2be (ccie2be@nyc.rr.com)
Date: Fri Dec 03 2004 - 08:37:35 GMT-3
Besides PBR and WCCP, does anybody know what other features require the sdm
setting to be changed from the default.
TIA, Tim
----- Original Message -----
From: "Geert Nijs" <geert.nijs@simac.be>
To: "Edi Guntoro" <eguntoro@sisindosat.co.id>; <ccielab@groupstudy.com>
Sent: Friday, December 03, 2004 2:47 AM
Subject: RE: PBR on cat 3550
> Check out this TAC note:
http://www.ciscotaccc.com/iprout/showcase?case=K11373857
>
> PBR on C3550 requires a change of the SDM template.
>
>
> Before you can enable policy routing, you must configure one of these
commands in the global configuration mode, and then the configuration must
be written and the switch reloaded:
>
> * sdm prefer extended-match
>
> * sdm prefer access extended-match
>
> * sdm prefer routing extended-match
>
> CAT3550(config)# access-list 10 permit 20.20.20.0 0.0.0.255
> CAT3550(config)# route-map pbr permit 10
> CAT3550(config-route-map)# match ip address 10
> CAT3550(config-route-map)# set ip next-hop 12.12.12.12
>
> CAT3550(config)# int vlan 3
> CAT3550(config-if)# ip policy route-map pbr
> CAT3550(config-if)#
> 06:12:31: %L3TCAM-3-SIZE_CONFLICT: PBR requires enabling extended routing
>
> CAT3550# show run int vlan 3
> Building configuration...
>
> Current configuration : 60 bytes
> !
> interface Vlan3
> ip address 55.55.55.1 255.255.255.0
>
> !--- Command not taken - you need to enable SDM.
>
> end
>
> CAT3550# conf t
> Enter configuration commands, one per line. End with CNTL/Z.
> CAT3550(config)# sdm prefer extended-match
> Changes to the running SDM preferences have been stored, but cannot take
effect
> until the next reload.
> Use 'show sdm prefer' to see what SDM preference is currently active.
> CAT3550(config)# end
>
> CAT3550# write
> 06:14:11: %SYS-5-CONFIG_I: Configured from console by console
> Building configuration...
> [OK]
>
> ltd-1-2# reload
> Proceed with reload? [confirm]
>
>
>
>
> Regards,
>
> Geert
> #13729
>
> ________________________________
>
> From: nobody@groupstudy.com on behalf of Edi Guntoro
> Sent: Thu 12/2/2004 5:03
> To: ccielab@groupstudy.com
> Subject: PBR on cat 3550
>
>
>
> Hi all,
> Why this message appear when I try to enable PBR on interface vlan, and
> the config was not succesfully added.
>
> %L3TCAM-3-SIZE_CONFLICT: PBR requires enabling extended routing
>
> Thanks
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
>
>
############################################################################
#########
> This e-mail and any attached files are confidential and may be legally
privileged.
> If you are not the addressee, any disclosure, reproduction, copying,
distribution,
> or other dissemination or use of this communication is strictly
prohibited.
> If you have received this transmission in error please notify Simac
immediately
> and then delete this e-mail.
>
> Simac has taken all reasonable precautions to avoid virusses in this
email.
> Simac does not accept liability for damage by virusses, for the correct
and complete
> transmission of the information, nor for any delay or interruption of the
transmission,
> nor for damages arising from the use of or reliance on the information.
>
> All e-mail messages addressed to, received or sent by Simac or Simac
employees
> are deemed to be professional in nature. Accordingly, the sender or
recipient of
> these messages agrees that they may be read by other Simac employees than
the official
> recipient or sender in order to ensure the continuity of work-related
activities
> and allow supervision thereof.
>
############################################################################
#########
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Mon Jan 03 2005 - 10:31:24 GMT-3