From: Kian Wah, Lai (kian_wah@qala.com.sg)
Date: Mon Oct 25 2004 - 14:35:39 GMT-3
Thanks. That solves the problem :)
Regards,
Kian Wah
Singapore Cisco User Group
http://www.sgcug.org
3 routers + one PIX rental at SGD2/hr or USD1.30/hr
http://rack.sgcug.org
Good for testing or practicing.
-----Original Message-----
From: Brian Dennis [mailto:bdennis@internetworkexpert.com]
Sent: Tuesday, October 26, 2004 1:29 AM
To: Kian Wah, Lai; Group Study
Subject: RE: Aux speed problem
Try using the speed command and not the rxspeed/txspeed command.
Router(config)#line aux 0
Router(config-line)#rxspeed 38400
Failed to change line 65's speed
Router(config-line)#speed 38400
Router(config-line)#do sho line 65
Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns
Int
65 AUX 38400/38400 - - - - - 0 0 0/0
-
Line 65, Location: "", Type: ""
Length: 24 lines, Width: 80 columns
Baud rate (TX/RX) is 38400/38400, no parity, 2 stopbits, 8 databits
Status: Ready, Modem Signals Polled
Capabilities: none
Modem state: Ready
Modem hardware state: noCTS noDSR DTR RTS
Special Chars: Escape Hold Stop Start Disconnect Activation
^^x none - - none
Timeouts: Idle EXEC Idle Session Modem Answer Session
Dispatch
00:10:00 never none not
set
Idle Session Disconnect Warning
never
Login-sequence User Response
00:00:30
Autoselect Initial Wait
not set
Modem type is unknown.
Session limit is not set.
Time since activation: never
Editing is enabled.
History is enabled, history size is 20.
DNS resolution in show commands is enabled
Full user help is disabled
Allowed input transports are none.
Allowed output transports are pad v120 telnet rlogin ssh.
Preferred transport is telnet.
No output characters are padded
No special data dispatching characters
Router(config-line)#
Router(config-line)#do sho ver | in 2600
IOS (tm) C2600 Software (C2600-IK9O3S3-M), Version 12.3(5b), RELEASE
SOFTWARE (fc1)
System image file is "flash:c2600-ik9o3s3-mz.123-5b.bin"
Brian Dennis, CCIE #2210 (R&S/ISP-Dial/Security)
bdennis@internetworkexpert.com
Internetwork Expert, Inc.
http://www.InternetworkExpert.com
Toll Free: 877-224-8987
Direct: 775-745-6404 (Outside the US and Canada)
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
Kian Wah, Lai
Sent: Sunday, October 24, 2004 10:42 PM
To: 'Group Study'
Subject: Aux speed problem
2620(config)#line aux 0
2620(config-line)#txspeed 38400
Failed to change line 65's speed
2620(config-line)#
Any clue why? It's the same for rxspeed. I even change the IOS and it's
the
same. Can't find any information on this at the archive or Cisco.
Regards,
Kian Wah
Singapore Cisco User Group
<http://www.sgcug.org> http://www.sgcug.org
3 routers + one PIX rental at SGD2/hr or USD1.30/hr
<http://rack.sgcug.org> http://rack.sgcug.org
Good for testing or practicing.
This archive was generated by hypermail 2.1.4 : Sat Nov 06 2004 - 17:11:52 GMT-3