From: Brian Dennis (bdennis@internetworkexpert.com)
Date: Fri Oct 22 2004 - 18:31:47 GMT-3
I'll chime in ;-) Here is a configuration of a router using a PVC to
communicate with an LS1010.
<Router-Config>
Rack1R6#sho run int atm0/0/0
Building configuration...
Current configuration : 101 bytes
!
interface ATM0/0/0
ip address 172.16.1.1 255.255.255.0
no atm ilmi-keepalive
pvc 0/500
!
end
Rack1R6#sho atm map
Map list ATM0/0/0_ATM_INARP : DYNAMIC
ip 172.16.1.10 maps to VC 1, VPI 0, VCI 500, ATM0/0/0
Rack1R6#ping 172.16.1.10
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.1.10, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms
Rack1R6#telnet 172.16.1.10
Trying 172.16.1.10 ... Open
User Access Verification
Password:
LS1010>exit
[Connection to 172.16.1.10 closed by foreign host]
Rack1R6#
</Router-Config>
<LS1010-Config>
LS1010#sho run int atm0/0/0
Building configuration...
Current configuration:
!
interface ATM0/0/0
description ATM to Rack1R6 ATM 0/0/0
end
LS1010#sho run int atm2/0/0
Building configuration...
Current configuration:
!
interface ATM2/0/0
ip address 172.16.1.10 255.255.255.0
atm pvc 0 500 encap aal5snap interface ATM0/0/0 0 500
end
LS1010#sho atm map
Map list LS1010 : PERMANENT
ip 172.16.1.1 maps to VC 32
, broadcast
LS1010#ping 172.16.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.1.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms
LS1010#
</LS1010-Config>
Brian Dennis, CCIE #2210 (R&S/ISP-Dial/Security)
bdennis@internetworkexpert.com
Internetwork Expert, Inc.
http://www.InternetworkExpert.com
Toll Free: 877-224-8987
Direct: 775-745-6404 (Outside the US and Canada)
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
Hoyle, Anthony (AL)
Sent: Friday, October 22, 2004 2:11 PM
To: 'Mestdagh, Mark [NCSBE - Non JJ]'; 'ccielab@groupstudy.com'
Subject: RE: LS1010 - Router
That's a good question. What will activate the other end of the PVC. I
have configured a 1010 from scratch
(sorta like a frame-relay switch) but I can't remember anything like
that.
You will need another router.
I guess the thinking would be to make the 1010 act as a Backbone
router...I
believe when you configure the
ATM device you are switching traffic from one interface to the other.
Nope
I don't think you can do it....but someone might chime in on this one
Final answer :)
Anthony Hoyle, CCIE #13948
EDS
Infrastructure Specialist
anthony.hoyle@eds.com
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
Mestdagh, Mark [NCSBE - Non JJ]
Sent: Friday, October 22, 2004 3:53 PM
To: 'ccielab@groupstudy.com'
Subject: LS1010 - Router
Hi
I've been looking for this on the net and archives but nothing to find.
Is
it possible to setup a PVC between a Router with atm module and a
LS1010?
Just that I don't have a second router with atm :)
Thx
Mark
This archive was generated by hypermail 2.1.4 : Sat Nov 06 2004 - 17:11:51 GMT-3