From: Richard Dumoulin (richard.dumoulin@vanco.es)
Date: Mon Jun 28 2004 - 19:43:40 GMT-3
You have to type "show ip eigrp nei" several times to see how the hold time
goes from 15 to 10 seconds. This is supposing that hello time is set to 5
sec and hold time 15 seconds .
See below for an example:
Router#sh ip ei nei
IP-EIGRP neighbors for process 200
H Address Interface Hold Uptime SRTT RTO Q Seq
(sec) (ms) Cnt Num
0 192.168.200.69 Se0 11 4d06h 272 1632 0 42340
IP-EIGRP neighbors for process 17
Router#sh ip ei nei
IP-EIGRP neighbors for process 200
H Address Interface Hold Uptime SRTT RTO Q Seq
(sec) (ms) Cnt Num
0 192.168.200.69 Se0 12 4d06h 272 1632 0 42340
IP-EIGRP neighbors for process 17
Router#sh ip ei nei
IP-EIGRP neighbors for process 200
H Address Interface Hold Uptime SRTT RTO Q Seq
(sec) (ms) Cnt Num
0 192.168.200.69 Se0 11 4d06h 272 1632 0 42340
IP-EIGRP neighbors for process 17
Router#sh ip ei nei
IP-EIGRP neighbors for process 200
H Address Interface Hold Uptime SRTT RTO Q Seq
(sec) (ms) Cnt Num
0 192.168.200.69 Se0 10 4d06h 272 1632 0 42340
IP-EIGRP neighbors for process 17
For the authentication I can t help, I have always supposed something is
wrong if the routes do not appear :)
--Richard
-----Original Message-----
From: Geert Nijs [mailto:geert.nijs@simac.be <mailto:geert.nijs@simac.be> ]
Sent: martes, 29 de junio de 2004 0:33
To: ccielab@groupstudy.com
Subject: EIGRP questions
Hi all,
Just two simple questions, which i just can't seem to find:
- How can you verify the EIGRP timers ?? How can i check the interval of my
hello packets on an interface ?
Is there a show command for this or do i really have to do a debug
(or know it by heart).
I am looking for a way to see the hello timings on an interface
(like when you do: show ip prot, for rip you can see: sending rip updates
every xx seconds,
ospf has his hello and dead timers listed in "show ip
ospf int"...and EIGRP ???)
- How can i verify if EIGRP is using my authentication keys ?? (with ospf,
you can do a "show ip ospf int", and the last line reads: "Message Digest
authentication
enabled"). Is there something like this for EIGRP also ??
Regards,
Geert
############################################################################
#
########
This e-mail and any attached files are confidential and may be legally
privileged. If you are not the addressee, any disclosure, reproduction,
copying, distribution, or other dissemination or use of this communication
is strictly prohibited. If you have received this transmission in error
please notify Simac immediately and then delete this e-mail.
Simac has taken all reasonable precautions to avoid virusses in this email.
Simac does not accept liability for damage by virusses, for the correct and
complete transmission of the information, nor for any delay or interruption
of the transmission, nor for damages arising from the use of or reliance on
the information.
All e-mail messages addressed to, received or sent by Simac or Simac
employees are deemed to be professional in nature. Accordingly, the sender
or recipient of these messages agrees that they may be read by other Simac
employees than the official recipient or sender in order to ensure the
continuity of work-related activities and allow supervision thereof.
############################################################################
#
########
This archive was generated by hypermail 2.1.4 : Sat Jul 03 2004 - 19:40:52 GMT-3