From: Carlos G Mendioroz (tron@huapi.ba.ar)
Date: Sat Jun 05 2004 - 09:30:58 GMT-3
One thing that could be making the difference is the registration that
ilmi does on the switch (a 1010 I guess).
That is not strictly necesary, but on the lab setup is the way the 1010
knows about your addresses. If you don't enable ilmi, you would need to
tell the ATM switch where the NSAPs live for it to be able to deliver
the call.
Koen Peetermans wrote:
> -----Original Message-----
> From: Koen Peetermans [mailto:K.Peetermans@chello.be]
> Sent: zaterdag 5 juni 2004 13:57
> To: 'Richard Dumoulin'
> Subject: RE: ATM SVC's and ILMI
>
> Hmmmmm. I've checked, I didn't forget the qsaal PVC.
>
> Solie only talks about the qsaal for SVC's. However,
> I can't get it working without ILMI...
>
> Koen
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> Richard Dumoulin
> Sent: zaterdag 5 juni 2004 13:38
> To: Koen Peetermans; ccielab@groupstudy.com
> Subject: RE: ATM SVC's and ILMI
>
> You need the signaling pvc 0/5 qsaal !! I believe this like enabling ISDN
> Q931. Although in ISDN it is automatically enabled,
>
> --Richard
>
> -----Original Message-----
> From: Koen Peetermans [mailto:K.Peetermans@chello.be]
> Sent: sabado, 05 de junio de 2004 10:32
> To: ccielab@groupstudy.com
> Subject: RE: ATM SVC's and ILMI
>
>
> (Sorry, pressed "send" involuntarily)
>
> Hi,
>
> I am practicing ATM on the CCIE4U remote lab.
>
> If you look in the Practical studies volume I book, Solie doesn't use ILMI
> for bringing up SVC's. However, I don't seem to get my SVC's working unless
> I enable the ILMI 0/16 pvc on the ATM main interface.
>
> The configuration looks like this:
>
>
>
> interface ATM0.99 multipoint
> ip address 10.10.10.2 255.255.255.0
> !
> svc nsap 47.00918100000000E01E35FB01.000800080008.00
> protocol ip 10.10.10.1 broadcast
> !
> atm nsap-address 47.00918100000000E01E35FB01.001200120012.00
>
> I don't think there is anything wrong with the config since enabling ILMI
> solves the problem.
>
> Could there be a way for doing it without using ILMI (perhaps an ATM static
> Route on the ATM switch ?)
>
> Kind regards,
>
> Koen.
>
> _______________________________________________________________________
> Please help support GroupStudy by purchasing your study materials from:
> http://shop.groupstudy.com
>
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
> _______________________________________________________________________
> Please help support GroupStudy by purchasing your study materials from:
> http://shop.groupstudy.com
>
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
> _______________________________________________________________________
> Please help support GroupStudy by purchasing your study materials from:
> http://shop.groupstudy.com
>
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
-- Carlos G Mendioroz <tron@huapi.ba.ar> LW7 EQI Argentina
This archive was generated by hypermail 2.1.4 : Sat Jul 03 2004 - 19:40:33 GMT-3