From: Mike Schlenger (mschlenger@meridianitsolutions.com)
Date: Wed Jun 02 2004 - 18:38:54 GMT-3
Actually, both h323-gateway commands are to be configured on the corresponding loopback interfaces. And yes, it has to be configured at both ends if that is was you are using in your session target instruction set.
Mike
Mike Schlenger
CCIE #7079
-----Original Message-----
From: Richard Dumoulin [mailto:richard.dumoulin@vanco.es]
Sent: Wed 6/2/2004 3:17 PM
To: Yasser Abdullah; Mike Schlenger; pbubienczyk@szczesliwice.pl; ccielab@groupstudy.com
Cc:
Subject: RE: Voice - source/destinationa ddresses
Hi Yasser, actually this is not what I asked. Mike provided two different commands. One to be applied on an interface and another one to be applied generally. So I wondered if both were required,
--Richard
-----Original Message-----
From: Yasser Abdullah [mailto:yasser@alharbitelecom.com]
Sent: miC)rcoles, 02 de junio de 2004 21:11
To: Richard Dumoulin; 'Mike Schlenger'; pbubienczyk@szczesliwice.pl; ccielab@groupstudy.com
Subject: RE: Voice - source/destinationa ddresses
I can't test this, but I think that if you want to control the source ip when calls are 'originating' from either gateway, you need the command on both ends.
Can someone test it?
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of Richard Dumoulin
Sent: Wednesday, June 02, 2004 5:02 PM
To: Mike Schlenger; pbubienczyk@szczesliwice.pl; ccielab@groupstudy.com
Subject: RE: Voice - source/destinationa ddresses
Hi Mike, should both commands be configured or one or the other ? The doc-cd says it is convenient but it is not clear,
Thanks
--Richard
-----Original Message-----
From: Mike Schlenger [mailto:mschlenger@meridianitsolutions.com]
Sent: miircoles, 02 de junio de 2004 15:29
To: pbubienczyk@szczesliwice.pl; ccielab@groupstudy.com
Subject: RE: Voice - source/destinationa ddresses
Take a look at these commands under your loopback interfaces.
H323-gateway voip interface
H323-gateway voip bind srcad <in lo0>
Mike
Mike Schlenger
CCIE #7079
-----Original Message-----
From: pbubienczyk@szczesliwice.pl [mailto:pbubienczyk@szczesliwice.pl]
Sent: Wednesday, June 02, 2004 8:23 AM
To: ccielab@groupstudy.com
Subject: Voice - source/destinationa ddresses
Hello
My voip dial peers are configured with ip addresses of loopback interfaces on both ends (with session target command). But the RTCP and RTP communication is going with addresses of others interfaces (serial in this particular case). Is there is some way to configure routers that all voice communication will be held by using only loopback interfaces.
Thx for your help - Peter
_______________________________________________________________________
Please help support GroupStudy by purchasing your study materials from: http://shop.groupstudy.com
Subscription information may be found at: http://www.groupstudy.com/list/CCIELab.html
_______________________________________________________________________
Please help support GroupStudy by purchasing your study materials from: http://shop.groupstudy.com
Subscription information may be found at: http://www.groupstudy.com/list/CCIELab.html
_______________________________________________________________________
Please help support GroupStudy by purchasing your study materials from: http://shop.groupstudy.com
Subscription information may be found at:
http://www.groupstudy.com/list/CCIELab.html
_______________________________________________________________________
Please help support GroupStudy by purchasing your study materials from: http://shop.groupstudy.com
Subscription information may be found at:
http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Sat Jul 03 2004 - 19:40:31 GMT-3