From: CCIE Canidate (cisco@heartofdarknessstudios.com)
Date: Wed May 05 2004 - 18:08:35 GMT-3
I keep getting an error that states that my SPIDs are not valid,
however I am using the spids that come wtih my simulator (11110101 and
22220101). I added these spids based upon other basic configs that I
could find, yet the example in KAslow's book don't have SPIDs.
Richard Dumoulin wrote:
> Tru shut no shut and then shi isdn stat to see if it says spid1 valid.
> Sorry I have no experience with isdn simulators cause I use real isdn !!
>
> -----Original Message-----
> From: CCIE Canidate [mailto:cisco@heartofdarknessstudios.com]
> Sent: miircoles, 05 de mayo de 2004 22:36
> To: Kenneth Wygand
> Cc: ccielab@groupstudy.com
> Subject: Re: Having trouble with Kaslow's ISDN example
>
>
> I am using an ISDN simulator, and have added the spids from my
> simulator. I am getting the following error:
>
> R2#sh isdn stat
> Global ISDN Switchtype = basic-ni
> ISDN BRI0 interface
> dsl 0, interface ISDN Switchtype = basic-ni
> Layer 1 Status:
> ACTIVE
> Layer 2 Status:
> TEI = 66, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
> TEI 66, ces = 1, state = 8(established)
> spid1 configured, spid1 NOT sent, spid1 NOT valid
> Layer 3 Status:
> 0 Active Layer 3 Call(s)
> Active dsl 0 CCBs = 0
> The Free Channel Mask: 0x80000003
> Total Allocated ISDN CCBs = 0
>
> This in a nutshell is telling me that my spids are not valid and not
> being sent. I am not sure of what I'm doing wrong at this point.
>
> Thanks,
>
> Kenneth Wygand wrote:
>
> >Hello,
> >
> >I am assuming you are using an ISDN simulator and not connecting the
> >router's BRI ports back-to-back, correct?
> >
> >Kenneth E. Wygand
> >Systems Engineer, Project Services
> >CISSP #37102, CCNP, CCDP, ACSP, Cisco IPT Design Specialist, MCP, CNA,
> >Network+, A+
> >Custom Computer Specialists, Inc.
> >"The only unattainable goal is the one not attempted."
> >-Anonymous
> >
> >-----Original Message-----
> >From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> >CCIE Canidate
> >Sent: Wednesday, May 05, 2004 4:09 PM
> >To: ccielab@groupstudy.com
> >Subject: Having trouble with Kaslow's ISDN example
> >
> >I have been trying to make the basic ISDN config in Kaslow's book to
> >work, but am having issues. This is my config:
> >
> >R1:
> >
> >interface BRI0
> > ip address 172.16.1.1 255.255.255.0
> > encapsulation hdlc
> > dialer string 2222
> > dialer-group 1
> > isdn switch-type basic-ni
> > isdn spid1 22220101 2222
> >
> >dialer-list 1 protocol ip permit
> >
> >R2:
> >interface BRI0
> > ip address 172.16.1.2 255.255.255.0
> > no ip directed-broadcast
> > dialer string 1111
> > dialer-group 1
> > isdn switch-type basic-ni
> > isdn spid1 11110101 1111
> >
> >
> >dialer-list 1 protocol ip permit ----------------------------------END
> >
> >I am trying to make this basic config work between 2 devices and am
> >getting stuffed. Can somebody point me in the right direction?
> >
> >Thanks!
> >
> >
> >ISDN Challenged guy
> >
> >_______________________________________________________________________
> >Please help support GroupStudy by purchasing your study materials from:
> >http://shop.groupstudy.com
> >
> >Subscription information may be found at:
> >http://www.groupstudy.com/list/CCIELab.html
> >
> >_______________________________________________________________________
> >Please help support GroupStudy by purchasing your study materials from:
> >http://shop.groupstudy.com
> >
> >Subscription information may be found at:
> >http://www.groupstudy.com/list/CCIELab.html
>
> _______________________________________________________________________
> Please help support GroupStudy by purchasing your study materials
> from: http://shop.groupstudy.com
>
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Wed Jun 02 2004 - 11:12:05 GMT-3