From: R&S Groupstudy (rsg@synergy-networking.co.uk)
Date: Wed Apr 14 2004 - 13:43:14 GMT-3
Tom,
Are you talking about the GSTACK gbics?
If so there's no extra config to do mate.
Note operation is at half duplex...... don't try and force it to full
Adam
!
interface GigabitEthernet0/1
switchport mode trunk
!
GigabitEthernet0/1 is up, line protocol is up
Hardware is Gigabit Ethernet, address is 0006.53bd.1234 (bia
0006.53bd.1234)
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive not set
Auto-duplex (Half), 1000Mb/s, media type is CX_GIGASTACK
output flow-control is off, input flow-control is off
ARP type: ARPA, ARP Timeout 04:00:00
GigaStack module(0.2) in GBIC slot. link1 is up, link2 is down
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Queueing strategy: fifo
Output queue 0/40, 36 drops; input queue 0/75, 0 drops
1 minute input rate 4374000 bits/sec, 921 packets/sec
1 minute output rate 7000 bits/sec, 7 packets/sec
562407108 packets input, 536952525 bytes, 0 no buffer
Received 448843709 broadcasts, 0 runts, 0 giants, 0 throttles
375203 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 278221541 multicast, 0 pause input
223611721 packets output, 2427157253 bytes, 0 underruns
0 output errors, 42529 collisions, 1 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of Tom
Young
Sent: 14 April 2004 16:44
To: Marvin Greenlee
Cc: ccielab@groupstudy.com
Subject: Re: Cat2950G-48's stack config
Marvin
Thank you for replying, but I think the file you give me
is not the stack document, it is the cluster setting.
I am configing the Cat2950's stack now, but not
successed. my switch is Cat4950G-48-EI, no problem with
IOS, and memory, Special GBIC and cable is also ok, But
couldn't done the stack, may I need some setting on switch
? How to confirm the stack status?
And who can provide me some document about the stack
config ?
Thanks alot
--- Marvin Greenlee <marvingreenlee@yahoo.com> $B$+$i$N%a(B
$B%C%;!<%8!'(B
> 2950 Clustering
>
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat2950/12114ea1/2950scg
/swclus.htm
>
> On the non-command switch, you need to configure the
> command switch MAC-address and cluster name
> ****
> cluster commander-address 000d.bbbb.bbbb member 2
> name
> MYCLUSTER
> <non-command switch>
>
> cluster enable MYCLUSTER 1
> <Command Switch>
> ****
> In this example, the command switch is member 1 and
> the non-command switch is member 2.
>
> Or, you can use the CMS interface.
>
> Marvin Greenlee
> Network Learning, Inc.
> www.ccbootcamp.com
>
> --- Tom Young <gitsyoung@yahoo.co.jp> wrote:
> > Hi , group
> >
> > Whould you please give me a config sample
> about
> > Cat2950G-48's stack ? I couldn't found anything
> from
> > cisco.com. And failured for making stack between
> > cat2950s. Really need someone's help.
> >
> > Thanks alot
>
>
>
>
> __________________________________
> Do you Yahoo!?
> Yahoo! Tax Center - File online by April 15th
> http://taxes.yahoo.com/filing.html
This archive was generated by hypermail 2.1.4 : Mon May 03 2004 - 19:48:47 GMT-3