From: Serran (groupstudy@swiftdsl.com.au)
Date: Sat Mar 20 2004 - 09:03:06 GMT-3
the thing is.. i don't need this command on a physical interface.
R5#sh run int s0/0
Building configuration...
Current configuration : 306 bytes
!
interface Serial0/0
ip address 150.50.100.5 255.255.255.224
encapsulation frame-relay
no arp frame-relay
frame-relay map ip 150.50.100.5 501
frame-relay map ip 150.50.100.2 501 broadcast
frame-relay map ip 150.50.100.6 501 broadcast
no frame-relay inverse-arp
end
As per normal.. this config works... now when i add in the frame-relay
interface-dlci 501 command... i cannot remove this unless removing the
static maps first... which is besides the point since this command is
irrelevant on a phsyical interface because the use of static maps...
hope my reasoning of questioning is a bit clearer...
cheers
Serran
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
SANCHEZ-MONGE,ANTONIO (HP-France,ex2)
Sent: Saturday, 20 March 2004 10:52 PM
To: 'Serran'; Ccielab@Groupstudy. Com
Subject: RE: Frame-relay interface-dlci command dependancy on physical
in t erfaces
"no frame-relay interface-dlci [dlci]" means "do NOT use this dlci in this
interface".
This is a contradiction since you are already using it through the map.
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
Serran
Sent: sabado, 20 de marzo de 2004 12:48
To: Ccielab@Groupstudy. Com
Subject: RE: Frame-relay interface-dlci command dependancy on physical int
erfaces
Just playing around with configurable options.. part of ipexpert chapter 3.
btw, a frame-relay interface-dlci command is not required on a physical
intf... all you need are static maps.
so my question is why is there a dependancy on this actual command
"frame-relay interface-dlci [dlci]" on a physical interface after this
command has been added after static maps. You cannot do a "no frame-relay
interface-dlci [dlci]" without first removing the static maps.
cheers
Serran
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
SANCHEZ-MONGE,ANTONIO (HP-France,ex2)
Sent: Saturday, 20 March 2004 10:40 PM
To: 'Serran'; Ccielab@Groupstudy. Com
Subject: RE: Frame-relay interface-dlci command dependancy on physical int
erfaces
Hi Serran,
A map statement binds a DLCI to an interface, regardless whether it is the
physical or a subinterface.
Why do you want to delete a DLCI referenced by a map? Maybe you want to add
the map to the subinterface?
Cheers,
Ato.
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
Serran
Sent: sabado, 20 de marzo de 2004 12:32
To: Ccielab@Groupstudy. Com
Subject: Frame-relay interface-dlci command dependancy on physical
interfaces
Hi All,
I understand the use of this command with ptp or ptmp sub intf's.. however
if I use this command on a physical intf (on a spoke router).. AND after I
have confirgured static maps, i cannot remove this command unless i have
removed the static maps first. The following IOS msg is parsed out:
R5(config-if)#no frame-relay interface-dlci 501
%Cannot remove PVC as being referenced by map statement R5(config-if)#
Is there any reason why the command seems to bind to the static maps when
not really required in the first place for a phy intf?
Thanks
Serran
This archive was generated by hypermail 2.1.4 : Thu Apr 01 2004 - 08:15:41 GMT-3