From: Arvind Yadav (arvindyadav@comcast.net)
Date: Mon Jan 26 2004 - 04:20:40 GMT-3
Here you go
http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122cgcr/fvvf
ax_c/vvfpeers.htm#1244361
----- Original Message -----
From: "chirag" <chiragshroff@myrealbox.com>
To: "Arvind Yadav" <arvindyadav@comcast.net>; <wwwjjang@chol.com>;
<ccielab@groupstudy.com>
Sent: Sunday, January 25, 2004 12:51 AM
Subject: Re: VoIP's Hunt-Group Test...
> arvind
>
> can u give send sample configuration of hunt-group in the same example
>
> thnx
> chirag shroff
>
> ----- Original Message -----
> From: "Arvind Yadav" <arvindyadav@comcast.net>
> To: <wwwjjang@chol.com>; <ccielab@groupstudy.com>
> Sent: Sunday, January 25, 2004 12:37 AM
> Subject: Re: VoIP's Hunt-Group Test...
>
>
> > Configuration looks fine.
> >
> > The lower the preference number, the higher the priority. Given below
> > example pnone B has the higher prority then phone A. Call should go to
> phone
> > B first, if phone B busy then only it will go to Phone A.
> >
> > Try with
> >
> > Router(config)# voice hunt {user-busy)
> >
> > Arvind
> >
> > ----- Original Message -----
> > From: <wwwjjang@chol.com>
> > To: <ccielab@groupstudy.com>
> > Sent: Saturday, January 24, 2004 10:12 AM
> > Subject: VoIP's Hunt-Group Test...
> >
> >
> > > Hi..Everyone..
> > >
> > > I'm studying VoIP Hunt-Group Test..
> > > But it doesn't work well..
> > >
> > > Who knows the reason ???
> > > Help me...
> > >
> > > --------
> > > Diagram
> > > --------
> > >
> > > Phone-A(1111)--R1-S0(1.1.1.1)-----s0(1.1.1.2)-R2----Phone-C(2222)
> > > /
> > > /
> > > Phone-B(1111)
> > >
> > > ----------
> > > Question
> > > ----------
> > > -I wish When Phone-C calls to the 1111,
> > > Phone-A should ring Only if Phone-B is in busy-state...
> > > -When Phone-B is not busy, Phone-B should ring..
> > > ----------
> > > My-Config
> > > ----------
> > >
> > > -----
> > > R1>
> > > ------
> > > dial-peer voice 1111 pots **>Phone-A
> > > preference 2 **
> > > destination-pattern 1111
> > > port 1/0/0
> > > !
> > > dial-peer voice 11111 pots **>Phone-B
> > > preference 1 **
> > > destination-pattern 1111
> > > port 1/0/1
> > > !
> > > dial-peer voice 2222 voip
> > > destination-pattern 2222
> > > session target ipv4:1.1.1.2
> > >
> > > -------
> > > BB3>
> > > ------------
> > > dial-peer voice 2222 pots
> > > destination-pattern 2222
> > > port 1/1/0
> > > !
> > > dial-peer voice 1111 voip
> > > destination-pattern 1111
> > > session target ipv4:1.1.1.1
> > >
> > > =>To test the clause "When Phone-C calls to the 1111,
> > > Phone-A should ring Only if Phone-B is in busy-state..."
> > > , I set the voice-port 1/0/1 to be in the Busy-state
> > > by configuring the command "busyout forced" under
> > > the voice-port 1/0/1 in R1.
> > > => And i call to the 1111 from Phone-C
> > > But Phone-A Don't call ring !!!!
> > >
> > > My configuration is not correct ??
> > > What's the correct answer ??
> > >
> > >
This archive was generated by hypermail 2.1.4 : Mon Feb 02 2004 - 09:07:50 GMT-3