From: Marvin Greenlee (marvingreenlee@yahoo.com)
Date: Thu Jan 01 2004 - 00:33:52 GMT-3
The dialer maps don't match the spids. Also, since
you are using ppp w/chap do you have
username/passwords configured? Have you tried
disabling the keepalives on the BRI? What does a
debug ppp auth show?
Sincerely,
Marvin Greenlee
--- Jeff Nelson <jnelson@rackspace.com> wrote:
> I guess I'm just looking for a reality check here,
> or at least some closure ;-)
>
> I've got R1 connected to R2 via bri0/0 with a
> basic-ni1 simulator and spids. Everything seems to
> work great save that traffic never seems to go
> across. Attempting to ping the other side brings up
> BRI0/0:1 but OSPF never forms an adjacency, it just
> times out after the idle-timeout and drops until the
> next ospf hello to 224.0.0.5. I've stipped all the
> fancy configs from the interfaces, but no change.
> The interface shows packets in and packets out. Then
> I tried to ping the router's own BRI interface IP
> and it cannot (is this normal?), so I'm like is GOD
> telling me to go drink on New Year's Eve?
>
> but seriously, this has got to be just a simulator
> problem, right?
> lab-r2#sh int bri0/0 1
> BRI0/0:1 is up, line protocol is up
> Hardware is PQUICC BRI
> MTU 1200 bytes, BW 64 Kbit, DLY 20000 usec,
> reliability 255/255, txload 1/255, rxload 1/255
> Encapsulation PPP, loopback not set
> Keepalive set (10 sec)
> Time to interface disconnect: idle 00:00:32
> LCP Open
> Open: IPCP, CDPCP
> Last input 00:00:02, output 00:00:02, output hang
> never
> Last clearing of "show interface" counters
> 00:16:44
> Input queue: 0/75/0/0 (size/max/drops/flushes);
> Total output drops: 0
> Queueing strategy: weighted fair
> Output queue: 0/1000/64/0 (size/max
> total/threshold/drops)
> Conversations 0/1/16 (active/max active/max
> total)
> Reserved Conversations 0/0 (allocated/max
> allocated)
> Available Bandwidth 48 kilobits/sec
> 5 minute input rate 0 bits/sec, 0 packets/sec
> 5 minute output rate 0 bits/sec, 0 packets/sec
> 272 packets input, 4464 bytes, 0 no buffer
> Received 0 broadcasts, 0 runts, 0 giants, 0
> throttles
> 0 input errors, 0 CRC, 0 frame, 0 overrun, 0
> ignored, 0 abort
> 434 packets output, 24881 bytes, 0 underruns
> 0 output errors, 0 collisions, 0 interface
> resets
> 0 output buffer failures, 0 output buffers
> swapped out
> 24 carrier transitions
>
>
> lab-r2#sh isdn status
> Global ISDN Switchtype = basic-ni
> ISDN BRI0/0 interface
> dsl 0, interface ISDN Switchtype = basic-ni
> Layer 1 Status:
> ACTIVE
> Layer 2 Status:
> TEI = 66, Ces = 1, SAPI = 0, State =
> MULTIPLE_FRAME_ESTABLISHED
> TEI = 67, Ces = 2, SAPI = 0, State =
> MULTIPLE_FRAME_ESTABLISHED
> TEI 66, ces = 1, state = 8(established)
> spid1 configured, no LDN, spid1 sent,
> spid1 valid
> Endpoint ID Info: epsf = 0, usid = 0,
> tid = 3
> TEI 67, ces = 2, state = 8(established)
> spid2 configured, no LDN, spid2 sent,
> spid2 valid
> Endpoint ID Info: epsf = 0, usid = 0,
> tid = 7
> Layer 3 Status:
> 1 Active Layer 3 Call(s)
> CCB:callid=801F, sapi=0, ces=1, B-chan=1,
> calltype=DATA
> Active dsl 0 CCBs = 1
> The Free Channel Mask: 0x80000002
> Total Allocated ISDN CCBs = 1
>
> ping 172.16.12.1
>
> Type escape sequence to abort.
> Sending 5, 100-byte ICMP Echos to 172.16.12.1,
> timeout is 2 seconds:
>
> 2w1d: ISDN BR0/0: TX -> SETUP pd = 8 callref = 0x20
> 2w1d: Bearer Capability i = 0x8890
> 2w1d: Channel ID i = 0x83
> 2w1d: Keypad Facility i = '2105550001'
> 2w1d: ISDN BR0/0: RX <- CALL_PROC pd = 8 callref =
> 0xA0
> 2w1d: Channel ID i = 0x89
> 2w1d: ISDN BR0/0: RX <- CONNECT pd = 8 callref =
> 0xA0
> 2w1d: %LINK-3-UPDOWN: Interface BRI0/0:1, changed
> state to up
> 2w1d: ISDN BR0/0: TX -> CONNECT_ACK pd = 8 callref
> = 0x20..
> 2w1d: %LINEPROTO-5-UPDOWN: Line protocol on
> Interface BRI0/0:1, changed state to up.
> 2w1d: %ISDN-6-CONNECT: Interface BRI0/0:1 is now
> connected to 2105550001 lab-r1..
> Success rate is 0 percent (0/5)
>
> lab-r2#sh run int bri0/0
> Building configuration...
>
> Current configuration : 287 bytes
> !
> interface BRI0/0
> ip address 172.16.12.2 255.255.255.0
> encapsulation ppp
> dialer idle-timeout 40
> dialer map ip 172.16.12.1 name r1 broadcast
> 2105550001
> dialer-group 1
> isdn switch-type basic-ni
> isdn spid1 21055500021
> isdn spid2 21055500022
> ppp authentication chap
> end
>
> lab-r1#sh run int bri0/0
> Building configuration...
>
> Current configuration : 253 bytes
> !
> interface BRI0/0
> ip address 172.16.12.1 255.255.255.0
> encapsulation ppp
> dialer map ip 172.16.12.2 name r2 broadcast
> 2105550002
> dialer-group 1
> isdn switch-type basic-ni
> isdn spid1 21055500011
> isdn spid2 21055500012
> ppp authentication chap
> end
>
>
> --the confus-ed
> j
>
>
__________________________________
Do you Yahoo!?
Protect your identity with Yahoo! Mail AddressGuard
http://antispam.yahoo.com/whatsnewfree
This archive was generated by hypermail 2.1.4 : Mon Feb 02 2004 - 09:07:35 GMT-3