From: miken (miken@sisna.com)
Date: Thu Jan 01 2004 - 00:33:27 GMT-3
Jeff,
Have you tried changing the name in your dialer map ip statement to match
what the remote router is actually sending? Take a look at the debug and see
what you think.
Run a debug ip packet detail while you are doing your pings. If you see
encapsulation failure, it is a good indication you have a map problem. That
will help you determine what the problem may be with pinging your local
interface.
lab-r2#
dialer map ip 172.16.12.1 name lab-r1 broadcast 2105550001
lab-r1#
dialer map ip 172.16.12.2 name lab-r2 broadcast 2105550002
Mike Nygard, CCIE#12602
----- Original Message -----
From: "Jeff Nelson" <jnelson@rackspace.com>
To: <ccielab@groupstudy.com>
Sent: Wednesday, December 31, 2003 8:07 PM
Subject: ISDN config (maybe a simulator problem?)
> I guess I'm just looking for a reality check here, or at least some
closure ;-)
>
> I've got R1 connected to R2 via bri0/0 with a basic-ni1 simulator and
spids. Everything seems to work great save that traffic never seems to go
across. Attempting to ping the other side brings up BRI0/0:1 but OSPF never
forms an adjacency, it just times out after the idle-timeout and drops until
the next ospf hello to 224.0.0.5. I've stipped all the fancy configs from
the interfaces, but no change. The interface shows packets in and packets
out. Then I tried to ping the router's own BRI interface IP and it cannot
(is this normal?), so I'm like is GOD telling me to go drink on New Year's
Eve?
>
> but seriously, this has got to be just a simulator problem, right?
> lab-r2#sh int bri0/0 1
> BRI0/0:1 is up, line protocol is up
> Hardware is PQUICC BRI
> MTU 1200 bytes, BW 64 Kbit, DLY 20000 usec,
> reliability 255/255, txload 1/255, rxload 1/255
> Encapsulation PPP, loopback not set
> Keepalive set (10 sec)
> Time to interface disconnect: idle 00:00:32
> LCP Open
> Open: IPCP, CDPCP
> Last input 00:00:02, output 00:00:02, output hang never
> Last clearing of "show interface" counters 00:16:44
> Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
> Queueing strategy: weighted fair
> Output queue: 0/1000/64/0 (size/max total/threshold/drops)
> Conversations 0/1/16 (active/max active/max total)
> Reserved Conversations 0/0 (allocated/max allocated)
> Available Bandwidth 48 kilobits/sec
> 5 minute input rate 0 bits/sec, 0 packets/sec
> 5 minute output rate 0 bits/sec, 0 packets/sec
> 272 packets input, 4464 bytes, 0 no buffer
> Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
> 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
> 434 packets output, 24881 bytes, 0 underruns
> 0 output errors, 0 collisions, 0 interface resets
> 0 output buffer failures, 0 output buffers swapped out
> 24 carrier transitions
>
>
> lab-r2#sh isdn status
> Global ISDN Switchtype = basic-ni
> ISDN BRI0/0 interface
> dsl 0, interface ISDN Switchtype = basic-ni
> Layer 1 Status:
> ACTIVE
> Layer 2 Status:
> TEI = 66, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
> TEI = 67, Ces = 2, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
> TEI 66, ces = 1, state = 8(established)
> spid1 configured, no LDN, spid1 sent, spid1 valid
> Endpoint ID Info: epsf = 0, usid = 0, tid = 3
> TEI 67, ces = 2, state = 8(established)
> spid2 configured, no LDN, spid2 sent, spid2 valid
> Endpoint ID Info: epsf = 0, usid = 0, tid = 7
> Layer 3 Status:
> 1 Active Layer 3 Call(s)
> CCB:callid=801F, sapi=0, ces=1, B-chan=1, calltype=DATA
> Active dsl 0 CCBs = 1
> The Free Channel Mask: 0x80000002
> Total Allocated ISDN CCBs = 1
>
> ping 172.16.12.1
>
> Type escape sequence to abort.
> Sending 5, 100-byte ICMP Echos to 172.16.12.1, timeout is 2 seconds:
>
> 2w1d: ISDN BR0/0: TX -> SETUP pd = 8 callref = 0x20
> 2w1d: Bearer Capability i = 0x8890
> 2w1d: Channel ID i = 0x83
> 2w1d: Keypad Facility i = '2105550001'
> 2w1d: ISDN BR0/0: RX <- CALL_PROC pd = 8 callref = 0xA0
> 2w1d: Channel ID i = 0x89
> 2w1d: ISDN BR0/0: RX <- CONNECT pd = 8 callref = 0xA0
> 2w1d: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to up
> 2w1d: ISDN BR0/0: TX -> CONNECT_ACK pd = 8 callref = 0x20..
> 2w1d: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0/0:1, changed
state to up.
> 2w1d: %ISDN-6-CONNECT: Interface BRI0/0:1 is now connected to 2105550001
lab-r1..
> Success rate is 0 percent (0/5)
>
> lab-r2#sh run int bri0/0
> Building configuration...
>
> Current configuration : 287 bytes
> !
> interface BRI0/0
> ip address 172.16.12.2 255.255.255.0
> encapsulation ppp
> dialer idle-timeout 40
> dialer map ip 172.16.12.1 name r1 broadcast 2105550001
> dialer-group 1
> isdn switch-type basic-ni
> isdn spid1 21055500021
> isdn spid2 21055500022
> ppp authentication chap
> end
>
> lab-r1#sh run int bri0/0
> Building configuration...
>
> Current configuration : 253 bytes
> !
> interface BRI0/0
> ip address 172.16.12.1 255.255.255.0
> encapsulation ppp
> dialer map ip 172.16.12.2 name r2 broadcast 2105550002
> dialer-group 1
> isdn switch-type basic-ni
> isdn spid1 21055500011
> isdn spid2 21055500012
> ppp authentication chap
> end
>
>
> --the confus-ed
> j
>
> _______________________________________________________________________
> Please help support GroupStudy by purchasing your study materials from:
> http://shop.groupstudy.com
>
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Mon Feb 02 2004 - 09:07:35 GMT-3