From: Ken.Farrington@barclayscapital.com
Date: Wed Nov 19 2003 - 05:29:15 GMT-3
Many thx guys :)) will try this afternoon :)
-----Original Message-----
From: Kurt Bergsbaken [mailto:kbergsbaken@yahoo.com]
Sent: 18 November 2003 23:09
To: Lloyd, Wayne; 'Ken.Farrington@barclayscapital.com';
ccielab@groupstudy.com
Subject: RE: aLaw and uLaw
2/3 orf the way down.
M2CORE2#sh voice port 6/0/0
Foreign Exchange Station 6/0/0 Slot is 6, Sub-unit is
0, Port is 0
Type of VoicePort is FXS
Operation State is DORMANT
Administrative State is UP
No Interface Down Failure
Description is not set
Noise Regeneration is enabled
Non Linear Processing is enabled
Non Linear Mute is disabled
Non Linear Threshold is -21 dB
Music On Hold Threshold is Set to -38 dBm
In Gain is Set to 0 dB
Out Attenuation is Set to 3 dB
Echo Cancellation is enabled
Echo Cancellation NLP mute is disabled
Echo Cancellation NLP threshold is -21 dB
Echo Cancel Coverage is set to 8 ms
Playout-delay Mode is set to adaptive
Playout-delay Nominal is set to 60 ms
Playout-delay Maximum is set to 200 ms
Playout-delay Minimum mode is set to default, value
40 ms
Playout-delay Fax is set to 300 ms
Connection Mode is normal
Connection Number is not set
Initial Time Out is set to 10 s
Interdigit Time Out is set to 10 s
Call Disconnect Time Out is set to 60 s
Ringing Time Out is set to 180 s
Wait Release Time Out is set to 30 s
Companding Type is u-law
Region Tone is set for US
Analog Info Follows:
Currently processing none
Maintenance Mode Set to None (not in mtc mode)
Number of signaling protocol errors are 0
Impedance is set to 600r Ohm
Station name None, Station number None
Translation profile (Incoming):
Translation profile (Outgoing):
Voice card specific Info Follows:
Signal Type is loopStart
Ring Frequency is 25 Hz
Hook Status is On Hook
Ring Active Status is inactive
Ring Ground Status is inactive
Tip Ground Status is inactive
Digit Duration Timing is set to 100 ms
InterDigit Duration Timing is set to 100 ms
No disconnect acknowledge
Ring Cadence is defined by CPTone Selection
Ring Cadence are [20 40] * 100 msec
Ringer Equivalence Number is set to 1
--- "Lloyd, Wayne" <WayneLl@lynxtec.com> wrote:
> Hi,
>
> You should be able to use the command "compand-type
> u-law|a-law" under the
> voice port configuration, I'm sure you can check the
> existing configuration
> by a "show voice port", I don't have the kit in
> front of me to check this as
> I'm waiting for some memory but if I remember
> rightly when checking a voice
> port you don't use the "-" between voice and port
> like you do when your'e
> configuring (might be wrong). However I think the
> reason why you can't see
> the command is because youre configuring an analog
> interface and I'm pretty
> sure that the companding type configuration is only
> required for digital
> interfaces.
>
> Thanks,
>
> -----Original Message-----
> From: Ken.Farrington@barclayscapital.com
> [mailto:Ken.Farrington@barclayscapital.com]
> Sent: 18 November 2003 21:47
> To: ccielab@groupstudy.com
> Subject: aLaw and uLaw
>
> Guys, just pulled this from the CD......for a Cisco
> 800
>
> Question is,
> How do you determine if an FXS uses alaw or ulaw on
> a 2600 router? Can you
> set it, how do you display it?
> The only thing I can find uner the voice-port 1/0/0
> command is cptone?
>
> Many thx indeed,
> Ken
>
>
>
> alaw and ulaw
> Specifies the pulse code modulation (PCM) encoding
> scheme for telephones,
> fax machines, or modems connected to a Cisco 800
> series router. The keywords
> are as follows:
>
> alaw-Specifies the ITU-T PCM encoding scheme used to represent analog
> voice samples as digital values.
> ulaw-Specifies the North American PCM encoding
> scheme used to represent
> analog voice samples as digital values.
> The default depends on the country chosen in the
> pots country command (on a
> cisco 800)
>
>
>
>
------------------------------------------------------------------------
> For more information about Barclays Capital, please
> visit our web site at http://www.barcap.com.
>
>
> Internet communications are not secure and therefore
> the Barclays
> Group does not accept legal responsibility for the
> contents of this
> message. Although the Barclays Group operates
> anti-virus programmes,
> it does not accept responsibility for any damage
> whatsoever that is
> caused by viruses being passed. Any views or
> opinions presented are
> solely those of the author and do not necessarily
> represent those of the
> Barclays Group. Replies to this email may be
> monitored by the Barclays
> Group for operational or business reasons.
>
>
------------------------------------------------------------------------
>
>
This archive was generated by hypermail 2.1.4 : Fri Dec 12 2003 - 12:29:14 GMT-3