From: Danny.Andaluz@triaton-na.com
Date: Tue Oct 21 2003 - 16:47:21 GMT-3
I see that now, Peter. Thanks.
Danny
-----Original Message-----
From: Peter [mailto:peter@cyscoexpert.com]
Sent: Tuesday, October 21, 2003 3:35 PM
To: ccielab@groupstudy.com
Subject: Re: Privilege Level Command
If you move "show run" to level 14 it will not show you anything, because in
order to see running-config you have to have privilege to all these commands
that make up the config. By default you only have access to the same
commands you have from level 1. So you can move "config t" to privilege
level 14, "interface" command and "ip address" command to level 14 and if
you "show run" you will only see the interfaces with ip addresses and
nothing else.
_____________________________
Peter
#7247 (R&S, Security, SP)
CyscoExpert Corp.
4433 W. Touhy Ave. Suite 410
Lincolnwood, IL 60712
Phone (847) 674-3392
Toll Free (866) CyscoXP (297-2697)
Fax (847) 674-2625
----- Original Message -----
From: <Danny.Andaluz@triaton-na.com>
To: <bdennis@internetworkexpert.com>; <ccielab@groupstudy.com>
Sent: Tuesday, October 21, 2003 2:23 PM
Subject: RE: Privilege Level Command
> That was part of the problem, but now it doesn't show me the whole
> config.
Just this small part:
>
> r2 con0 is now available
>
>
>
>
>
> Press RETURN to get started.
>
>
>
> User Access Verification
>
> Username: danny
> Password:
> r2#sh run
> Building configuration...
>
> Current configuration : 13 bytes
> !
> !
> !
> !
> end
>
> r2#sh priv
> Current privilege level is 14
> R2
>
> -----Original Message-----
> From: Brian Dennis [mailto:bdennis@internetworkexpert.com]
> Sent: Tuesday, October 21, 2003 2:46 PM
> To: Andaluz, Danilo, Triaton/NA; ccielab@groupstudy.com
> Subject: RE: Privilege Level Command
>
>
> Try changing it to "show running-config". "show running-configuration"
> is
not a valid command.
>
> Brian Dennis, CCIE #2210 (R&S/ISP-Dial/Security)
bdennis@internetworkexpert.com
> Toll Free: 877-224-8987
> Direct: 775-745-6404 (Outside the US and Canada)
> Internetwork Expert, Inc.
> http://www.InternetworkExpert.com
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf
> Of
Danny.Andaluz@triaton-na.com
> Sent: Tuesday, October 21, 2003 11:17 AM
> To: ccielab@groupstudy.com
> Subject: Privilege Level Command
>
> Hey Group,
>
> privilege exec level 14 show running-configuration
>
> username danny privilege 14 password 0 cisco
>
> How does the above privilege command NOT allow this user to issue this
command. I would think that using this privilege command makes "show run" a
level 14 command. However, it doesn't let me issue the command when I login
with username danny. Any ideas?
>
> Thanks,
> Danny
>
> ______________________________________________________________________
> _
> Please help support GroupStudy by purchasing your study materials from:
http://shop.groupstudy.com
>
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
> ______________________________________________________________________
> _
> Please help support GroupStudy by purchasing your study materials from:
> http://shop.groupstudy.com
>
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Mon Nov 24 2003 - 07:53:06 GMT-3